D-Link DVG-5112S Скачать руководство пользователя

Страница: 77 / 98

DVG-5112S User’s Manual

MAINTENANCE

D-Link Systems, Inc.

3-3-4 Dynamic DNS

ADVANCED

→

Dynamic DNS

Enable Dynamic DNS:

Check the box to enable DDNS function. It is only necessary when the VoIP

Telephone Adapter is set up behind an Internet sharing device that uses a dynamic IP address and does
not support DDNS.

Server Address:

Select a DDNS service from the drop and down arrow.

Hostname:

Enter the URL of the system (or NAT) – applied from domain name registration providers (e.g.

www.dyndns.org).

Username or Key/Password or Key:

Enter the Login ID and password used to log-in to the DDNS server.

Note:

If the VoIP Telephone Adapter is set up under NAT, then enter the hostname in the NAT IP/Domain

that is the same as the Hostname of the DDNS.

Содержание DVG-5112S



































































































Результаты поиска

Содержание DVG-5112S

Отзывы:

Похожие инструкции для DVG-5112S

Бренды по названию

Популярные бренды

D-Link DVG-5112S, Руководство пользователя

Результаты поиска

Содержание DVG-5112S

Отзывы:

Похожие инструкции для DVG-5112S

Бренды по названию

Популярные бренды