D-Link DVG-5112S Скачать руководство пользователя

Страница: 72 / 98

DVG-5112S User’s Manual

ADVANCED

D-Link Systems, Inc.

Route Mask:

Subnet mask to apply on destination network.

Next Hop IP:

The next hop IP address to the specified network.

Interface:

The interface attached to this route.

3-2-4-5 UPnP

ADVANCED

→

Advanced Network

→

UPnP

Enable UPnP:

Check the box to enable the VoIP TA’s IP traffic to pass through an Internet sharing device.

This function only works when the Internet sharing device supports UPnP and has it enabled.

Note:

The “Status

Current Status” page will show the status of UPnP.

3-2-4-6 SNMP

ADVANCED

→

Advanced Network

→

SNMP

Enable SNMP Agent:

Enable SNMP if selected.

Get/Set/Trap Community:

Enter Community name to Read, Write and Trap.

Trap Host:

Enter the IP of the Trap Host.

Содержание DVG-5112S



































































































Результаты поиска

Содержание DVG-5112S

Отзывы:

Похожие инструкции для DVG-5112S

Бренды по названию

Популярные бренды

D-Link DVG-5112S, Руководство пользователя

Результаты поиска

Содержание DVG-5112S

Отзывы:

Похожие инструкции для DVG-5112S

Бренды по названию

Популярные бренды