D-Link DVG-5112S Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 98

D-Link DVG-5112S Скачать руководство пользователя страница 17

DVG-5112S User’s Manual

SETUP

D-Link Systems, Inc.

17

3-1 SETUP

3-1-1 Internet Setup

WAN (Wide Area Network) Settings are used to connect to your ISP (Internet Service Provider). The WAN
settings are provided to you by your ISP and oftentimes referred to as "public settings". Please select the
appropriate option for your specific ISP.

IP Configuration (Setting WAN Port)

There are five methods of obtaining a WAN port IP address:

1.

DHCP, which means a Dynamic IP (Cable Modem)

2. Static

IP

3.

PPPoE (dial-up ADSL)

4. PPTP

Methods for using DHCP and PPPoE for obtaining an IP address may vary. If you are not familiar with
creating a network connection, please contact your local ISP.

After selecting the suitable option, click

Accept

at the bottom of the screen to save the settings.

You need to save the changes and restart the VoIP Telephone Adapter to make the changes active. Saving
the settings: Click

MAINTENANCE

and select

Backup and Restore

from the left menu. Tick

Save All

Settings

, then click

Reboot

. Wait for about 40 seconds before the VoIP Telephone Adapter obtaining an

IP address by the method you selected.

Note:

When the system has obtained a new IP address, and you are using a WAN port to enter the Web

Configuration Screen, the new IP address has to be used before you can get connected to the VoIP
Telephone Adapter. The same principle applies to the next two settings.

«
...
15
16
17
18
19
...
»

Содержание DVG-5112S



































































































Отзывы:

Нет отзывов