D-Link DVG-5112S Скачать руководство пользователя

Страница: 29 / 98

DVG-5112S User’s Manual

SETUP

D-Link Systems, Inc.

3-1-3 LAN Settings

SETUP

→

LAN Setup

Interface Mode:

Select the VoIP TA serving as a

Router

with NAT or

Bridge

between WAN port and LAN

port without NAT.

Note:

It is still accessible if LAN Interface Mode is Bridge.

LAN Port Address:

Enter the LAN IP address of the VoIP TA. It is also the default gateway for DHCP

clients.

Subnet Make:

Enter the subnet mask for DHCP clients.

Enable DHCP Server:

This variable is to assign the IP address for the devices connected to LAN port of

the VoIP TA.

IP Pool Starting Address:

Enter the starting IP address for the DHCP server's IP assignment.

IP Pool Ending Address:

Enter the ending IP address for the DHCP server's IP assignment.

Содержание DVG-5112S



































































































Результаты поиска

Содержание DVG-5112S

Отзывы:

Похожие инструкции для DVG-5112S

Бренды по названию

Популярные бренды

D-Link DVG-5112S, Руководство пользователя

Результаты поиска

Содержание DVG-5112S

Отзывы:

Похожие инструкции для DVG-5112S

Бренды по названию

Популярные бренды