D-Link DSL-562T Скачать руководство пользователя страница 75

Страница: 75 / 89

DSL-562T ADSL Router User

’

s Guide

Technical Specifications

GENERAL

Standards:

ITU G.992.1 (G.dmt)

ITU G.992.2 (G.lite)

ITU G.994.1 (G.Hs)

ITU-T Rec. I.361

ITU-T Rec. I.610

IEEE 802.3

IEEE 802.3u

IEEE 802.1d

RFC 791 (IP Routing)

RFC 792 (UDP)

RFC 826 (ARP)

RFC 1058 (RIP 1)

RFC 1389 (RIP 2)

RFC 1213 compliant

RFC 1483 (Bridged Ethernet)

RFC 1577 (IP over ATM)

RFC 1661 (PPP)

RFC 1994 (CHAP)

RFC 1334 (PAP)

RFC 2364 (PPP over ATM)

RFC 1631 (NAT)

RFC 1877 (Automatic IP
assignment)

RFC 2516 (PPP over Ethernet)

Supports RFC 2131 and RFC
2132 (DHCP)

Compatible with all T1.413
issue 2 (full rate DMT over
analog POTS), and CO DSLAM
equipment

Supports ATM Forum UNI V3.1
PVC

Protocols:

TCP/IP

UDP

RIP-1

RIP-2

IGMP

DHCP

BOOTP

ARP

AAL5

Data Transfer
Rate:

G.dmt full rate: Downstream up to 8 Mbps

Upstream up to 640 Kbps

G.lite: Downstream up to 1.5 Mbps

Upstream up to 512 Kbps

Media Interface:

RJ-11 port ADSL telephone line connection

RJ-45 port for 10/100BASET Ethernet connection

USB port

Содержание DSL-562T


























































































Результаты поиска

Содержание DSL-562T

Отзывы:

Похожие инструкции для DSL-562T

Бренды по названию

Популярные бренды

D-Link DSL-562T, Руководство пользователя

Результаты поиска

Содержание DSL-562T

Отзывы:

Похожие инструкции для DSL-562T

Бренды по названию

Популярные бренды