D-Link Dis-200G Series Скачать руководство пользователя страница 109

Страница: 109 / 269

DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide

105

Switch(config)# snmp-server enable traps loopback-detection.
Switch(config)#

22.

Mirror Commands

22-1

monitor session destination interface

This command is used to configure the destination interface for a port monitor session, allowing packets on

source ports to be monitored via a destination port. Use the

form of this command to delete a port monitor

session or remove the destination interface of the session.

monitor session

SESSION-NUMBER

destination interface

INTERFACE-ID

no monitor session

SESSION-NUMBER

destination interface

INTERFACE-ID

no monitor session

SESSION-NUMBER

Parameters

session

SESSION-NUMBER

Specifies the session number for the port monitor session. The valid

range is 1.

interface

INTERFACE-ID

Specifies the destination interface for the port monitor session.

Default

None.

Command Mode

Global Configuration Mode.

Command Default Level

Level: 15.

Usage Guideline

Use this command to configure the destination interface for a local monitor session. For a monitor session,

multiple source interfaces can be specified, but only one destination interface can be specified.

Example

This example shows how to create a port monitor session with the session number 1. It assigns a physical port

ethernet 1/0/1 as the destination port and three physical ports (ethernet 1/0/2 to ethernet1/0/4) as monitor

source ports.

Switch# configure terminal
Switch(config)# monitor session 1 destination interface Ethernet 1/0/1
Switch(config)# monitor session 1 source interface Ethernet 1/0/2-4
Switch(config)#

22-2

monitor session source interface

This command is used to configure the source port of a port monitor session. Use the

form of this command

to remove a port monitor session or remove a source port from the port monitor session.

Содержание Dis-200G Series














































































































































































































































































Результаты поиска

Содержание Dis-200G Series

Отзывы:

Похожие инструкции для Dis-200G Series

Бренды по названию

Популярные бренды

D-Link Dis-200G Series, Справочное руководство CLI

Результаты поиска

Содержание Dis-200G Series

Отзывы:

Похожие инструкции для Dis-200G Series

Бренды по названию

Популярные бренды