D-Link DGS-1100-16/ME Скачать руководство пользователя страница 58

Страница: 58 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

DOWNLOAD/UPLOAD COMMANDS

The Download/Upload commands in the Command Line Interface (CLI) are listed (along with the

appropriate parameters) in the following table.

Command

Parameter

download

{ firmware_fromTFTP <ipaddr> <path_filename (64)> image_id <value (1-2)> |

cfg_fromTFTP <ipaddr> <path_filename (64)> [ running_cfg | starup_cfg ] }(1)

upload

{ firmware_toTFTP <ipaddr> <path_filename (64)> image_id <1,2> | cfg_toTFTP

<ipaddr> <path_filename (64)> [ include_password | exclude_password ] }(1)

Each command is listed in detail, as follows:

download

Purpose

To download and install a firmware, boot, or switch configuration file

from a TFTP server.

Syntax

download { firmware_fromTFTP <ipaddr> <path_filename (64)>

image_id <value (1-2)> | cfg_fromTFTP <ipaddr>

<path_filename (64)> [ running_cfg | starup_cfg ] }(1)

Description

The

download

command downloads a firmware, boot, log or switch

configuration file from a TFTP server.

Parameters

fir

mware_fromTFTP −

Downloads and installs firmware on the

Switch from a TFTP server.

<ipaddr> −

The IPv4 address of the TFTP server.

<path_filename 64> −

The DOS path and filename of the switch

configuration file, up to 64 characters, on the TFTP server. For

example, C:\31xx.had.

image_id <value (1-2)> -

The firmware file installs on the image 1 or

cfg_fromTFTP −

Downloads a switch configuration file from a TFTP

server.

running_cfg -

Indicates the Configuration file is to be downloaded to

the running config.

starup_cfg −

Indicates the Configuration file is to be downloaded to

the startup config.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To download a firmware file:

DGS-1100-24P/ME:admin#download firmware_formTFTP 10.90.90.45 DGS1100-

fw_1.00.L001.flash image_id 1
Command : download firmware_formTFTP 10.90.90.45 DGS1100-fw_1.00.L001.flash

image_id 1

Содержание DGS-1100-16/ME






















































































































































































Результаты поиска

Содержание DGS-1100-16/ME

Отзывы:

Похожие инструкции для DGS-1100-16/ME

Бренды по названию

Популярные бренды

D-Link DGS-1100-16/ME, Справочное руководство

Результаты поиска

Содержание DGS-1100-16/ME

Отзывы:

Похожие инструкции для DGS-1100-16/ME

Бренды по названию

Популярные бренды