D-Link DGS-1100-16/ME Скачать руководство пользователя страница 144

Страница: 144 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

ZONE DEFENSE COMMANDS

The Zone Defense commands in the Command Line Interface (CLI) are listed (along with the appropriate

parameters) in the following table.

Command

Parameter

enable zone_defense

disable zone_defense

show zone_defense

Each command is listed in detail, as follows:

enable zone_defense

Purpose

To enable zone defense support of the switch.

Syntax

enable zone_defense

Description

The

enable zone_defense

command enables zone defense support

of the switch.

Parameters

None.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To enable zone defense support

DGS-1100-24P/ME:admin#enable zone_defense
Command : enable zone_defense

Success.

DGS-1100-24P/ME:admin#

disable zone_defense

Purpose

To disable zone defense support of the switch.

Syntax

disable zone_defense

Description

The

disable zone_defense

command disables zone defense

support of the switch.

Parameters

None.

Restrictions

Only administrator-level users can issue this command.

135

Содержание DGS-1100-16/ME






















































































































































































Результаты поиска

Содержание DGS-1100-16/ME

Отзывы:

Похожие инструкции для DGS-1100-16/ME

Бренды по названию

Популярные бренды

D-Link DGS-1100-16/ME, Справочное руководство

Результаты поиска

Содержание DGS-1100-16/ME

Отзывы:

Похожие инструкции для DGS-1100-16/ME

Бренды по названию

Популярные бренды