D-Link DGS-1100-16/ME Скачать руководство пользователя страница 162

Страница: 162 / 181

DGS-1100/ME Metro Ethernet Managed Switch CLI Reference Guide

Example usage:

To set the surveillance priority 5:

DGS-1100-24P/ME:admin#config voice_vlan priority 5
Command : config voice_vlan priority 5

Success.

DGS-1100-24P/ME:admin#

config voice_vlan aging_time

Purpose

Configures Voice VLAN aging time.

Syntax

config voice_vlan aging_time <min 1-65535>

Description

To set the aging time of the Voice VLAN. If the port is an automatic

Voice VLAN member, the aging time will be used to remove a port

from the Voice VLAN. The Voice VLAN aging timer will start when

the last voice device stops sending traffic and the MAC address of

this voice device is timed out, The port will be removed from the

Voice VLAN after it expires. When the voice traffic resumes during

the aging time, the aging timer will reset and stop.

Parameters

<min 1-65535>

- The aging time to set, the range is 1–65535

minutes.
The default value is 720 minutes.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To set the aging time of the Voice VLAN to 600 minutes:

DGS-1100-24P/ME:admin#config voice_vlan aging_time 600
Command : config voice_vlan aging_time 600

Success.

DGS-1100-24P/ME:admin#

153

Содержание DGS-1100-16/ME






















































































































































































Результаты поиска

Содержание DGS-1100-16/ME

Отзывы:

Похожие инструкции для DGS-1100-16/ME

Бренды по названию

Популярные бренды

D-Link DGS-1100-16/ME, Справочное руководство

Результаты поиска

Содержание DGS-1100-16/ME

Отзывы:

Похожие инструкции для DGS-1100-16/ME

Бренды по названию

Популярные бренды