CYP CDPS-P314EDC страница 10 Скачать руководство пользователя

Страница: 10 / 68

6.2 Rear Panel

L+ L- G R+ R-

AUDIO OUT

HDMI OUT

DC 12V

RS-232

LAN

HDMI IN

AUDIO IN

LAN(POE)

OUT

TX RX

AUDIO OUT 5-pin Terminal Block:

Connect to powered speakers or an

amplifier for analog stereo audio output.

Note: Only LPCM 2.0 sources are supported.

HDMI OUT Port:

Connect to an HDMI TV, monitor, or amplifier for digital

video and audio output.

HDMI IN Port:

Connect to HDMI source equipment such as a media

player, game console, or set-top box.

AUDIO IN Port:

Connect to the analog stereo output of a device such as

an audio player or PC.

LAN Ports:

Both ports are linked by an internal 2 port switch. Connect

either of these ports to a network switch, router, PC, or another

transceiver for transmission/reception of streamed video as well as to

control the unit via Telnet or WebGUI.

Note: This unit can be powered via PoE when the LAN(PoE) port is
directly connected to a Gigabit Ethernet switch that provides PoE
(802.3at).

RS-232 3-pin Terminal Block:

Connect to a PC, laptop, or serial

controllable device for the extension of RS-232 signals.

IR OUT Port:

Connect to an IR Blaster to transmit IR signals from a

connected transceiver to devices within direct line-of-sight of the IR

Blaster.

IR IN Port:

Connect to an IR Extender to receive local IR control signals

and extend them to devices located near a connected transceiver.

Ensure that the remote being used is within direct line-of-sight of the IR

Extender.

DC 12V Port:

Plug the 12V DC power adapter into this port and connect

it to an AC wall outlet for power.

Содержание CDPS-P314EDC





































































Результаты поиска

Содержание CDPS-P314EDC

Отзывы:

Похожие инструкции для CDPS-P314EDC

Бренды по названию

Популярные бренды

CYP CDPS-P314EDC, Руководство по эксплуатации

Результаты поиска

Содержание CDPS-P314EDC

Отзывы:

Похожие инструкции для CDPS-P314EDC

Бренды по названию

Популярные бренды