Cygnus Cygnus 2 Скачать руководство пользователя страница 11

Страница: 11 / 65

M5-CYG2P-M-01_Iss6.doc

Cygnus 2+ Operating Manual

To avoid damage from leaking batteries always remove the

batteries if the gauge will be unused for any length of time.

If the batteries run flat they may leak acid into the battery

compartment and damage the electrical contacts. This would

not be covered by the warranty.

Connecting the Probe

The Cygnus probe lead uses a custom made cable that offers

superior flexibility and resistance to oils and ultraviolet light. The

cable will not stiffen after exposure to ultraviolet light.

The connector uses original Lemo connectors for reliability. The

twin connectors are over-mounded to form a tough housing that

will provide a long lasting probe cable

The connector is orientated with a ‘pip’ and can only be plugged in

one-way around.

Depending on the type

of probe supplied the

probe end will have

either a twin Lemo 00,

BNC or single Lemo 00

connector.

Содержание Cygnus 2


































































Результаты поиска

Содержание Cygnus 2

Отзывы:

Похожие инструкции для Cygnus 2

Бренды по названию

Популярные бренды

Cygnus Cygnus 2, Руководство по эксплуатации

Результаты поиска

Содержание Cygnus 2

Отзывы:

Похожие инструкции для Cygnus 2

Бренды по названию

Популярные бренды