Cygnus Cygnus 2 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 65

background image

Cygnus 2+ Operating Manual

M5-CYG2P-M-01_Iss6.doc

44

3.

Press the Menu key to change

the value

4.

Use the Up and Down Select

keys to switch from mm to Inch

5.

When done press the Menu key

to save the new value.

Or press the Power / Cancel to

exit without saving.

Deep Coat Function (multiple echo mode)

The Deep Coat function is not available from the Main Menu

by default. To show the Deep Coat option in the menu please

contact Cygnus for instructions.

In Multiple Echo mode with the Deep Coat turned Off the gauge

can measure through most protective coatings up to 3 mm (0.11”)

thick when using a S2C type probe. Coatings like paint, anti-foul,

hard plastics and epoxy should present no problems as long as

they have not de-laminated/de-bonded from the metal surface.

In Multiple Echo mode with Deep Coat turned On will allow the

gauge to measure through coatings over 3mm (0.11”) thick up to

a maximum of around 20 mm (0.78”) depending on the properties

of the coating material.

Measuring through thick coatings is ultimately limited by how well

the coating material allows the ultrasound to pass through, soft

«
...
42
43
44
45
46
...
»

Содержание Cygnus 2


































































Отзывы:

Нет отзывов

Похожие инструкции для Cygnus 2

Бренд: F.W. Bell Страницы: 75

Бренд: Datavideo Страницы: 26

Бренд: Datcon Страницы: 84

Бренд: X-laser Страницы: 17

Бренд: ETI Страницы: 2

Бренд: Ratek Страницы: 24

Бренд: Oldham Страницы: 106

Бренд: YATO Страницы: 52

Бренд: Heyl Страницы: 2

Бренд: Amrutha Technologies Страницы: 22

Бренд: Straightpoint Страницы: 24

Бренд: Hanna Instruments Страницы: 2

Бренд: WIKA Страницы: 56

TRAVELER 3D ARM

Бренд: GRAVITY Страницы: 2

Бренд: K&K Sound Страницы: 2

Бренд: ATD Tools Страницы: 2

ISOLGUARD HIG93

Бренд: hakel Страницы: 15

Бренд: Radiation Alert Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды