Cubix Xpander Rack Mount 8 4U Скачать руководство пользователя страница 5

Страница: 5 / 14

Cubix Corporation



2800 Lockheed Way



Carson City, NV 89706-0

713 ● Page 5

Sales 800.829.0550



http://www.cubix.com



[email protected]



xpander-rackmount8-4u-g3 20140317

7. This step applies to MIBs with four slots for double-wide GPUs and a

PCIe x16 cable connection in the Rack Mount 8 enclosure. Confirm that
the Cable Link LED (P0) lights green for each MIB inside the Rack
Mount 8 enclosure.

Xpander MIBs are functioning properly once

each Cable LED (P0) lights green. Proceed to the

next step to install adapters.

8. Switch off AC power to the host computer(s). Leave the power cords and the external PCIe

cables to the host computer(s) connected.

9. Remove the two screws at each end of the rear ventilation panel above the rear Input /

Output (I/O) panel, remove the ventilation panel and set it aside temporarily.

10. Remove the screws for holding down the PCIe card end brackets.

Содержание Xpander Rack Mount 8 4U















Результаты поиска

Содержание Xpander Rack Mount 8 4U

Отзывы:

Похожие инструкции для Xpander Rack Mount 8 4U

Бренды по названию

Популярные бренды

Cubix Xpander Rack Mount 8 4U, Руководство пользователя

Результаты поиска

Содержание Xpander Rack Mount 8 4U

Отзывы:

Похожие инструкции для Xpander Rack Mount 8 4U

Бренды по названию

Популярные бренды