Cub Cadet 726 TDE Скачать руководство пользователя страница 26

Страница: 26 / 32

Troubleshooting

Problem

Cause

Remedy

Engine fails to start

Fuel tank empty, or stale fuel.

Blocked fuel line.

Choke not in the RUN position.

Faulty spark plug.

Key not in ignition switch on engine.

Spark plug wire disconnected.

Primer button not being used properly.

Fill tank with clean, fresh gasoline. Fuel

becomes stale after thirty days.

Clean the fuel line.

Move choke control to RUN position

Clean, adjust gap or replace.

Insert the key fully into the switch.

Connect spark plug wire.

Refer to the Operation Section.

Engine running erratically/

inconsistent RPM (hunting

or surging)

Engine running on CHOKE.

Fuel line blocked or stale fuel.

Water or dirt in fuel system.

Carburetor out of adjustment.

Over-governed engine.

Move choke control to RUN position.

Clean fuel line and fill tank with fresh clean,

gasoline.

Run engine until it stops. Refill with fresh fuel.

Contact an authorized service center.

Loss of power

Spark plug wire loose.

Gas cap vent hole plugged.

Connect and tighten spark plug wire.

Remove ice and snow from gas cap. Be

certain vent hole is clear.

Excessive vibration

Loose parts or damaged auger.

Stop the engine immediately and disconnect

the spark plug wire. Tighten all bolts and

nuts. If vibration continues, have the snow

thrower serviced by an authorized service

dealer.

Snow Thrower fails to

propel itself

Drive control cable in need of adjustment.

Drive belt loose or damaged.

Friction wheel worn.

Adjust drive control cable. Refer to

Maintenance & Adjustments Section.

Replace drive belt. Refer to the Service

Section.

Replace the friction wheel.

Snow Thrower fails to

discharge snow

Chute assembly clogged.

Shear pin(s) sheared.

Foreign object lodged in auger.

Auger control cable in need of adjustment.

Auger belt loose or damaged.

Stop engine and disconnect spark plug wire.

Clean chute and inside of auger housing with

clean-out tool or a stick.

Replace shear pin(s).

Stop engine immediately and disconnect

spark plug wire. Remove object from auger.

Adjust auger control cable. Refer to the

Maintenance & Adjustments Section.

Refer to Service Section.

Содержание 726 TDE

































Результаты поиска

Содержание 726 TDE

Отзывы:

Похожие инструкции для 726 TDE

Бренды по названию

Популярные бренды

Cub Cadet 726 TDE, Руководство оператора

Результаты поиска

Содержание 726 TDE

Отзывы:

Похожие инструкции для 726 TDE

Бренды по названию

Популярные бренды