background image

The limited warranty set forth below is given by Cub Cadet LLC with 

respect to new merchandise purchased and used in the United States, 

its possessions and territories, and by MTD Products Limited with 

respect to new merchandise purchased and used in Canada and/or its 

territories and possessions.
For non-commercial use: Cub Cadet warrants this product (excluding 

Normal Wear Parts

, as described below) against defects in material 

and workmanship for a period of three (3) years from the date of 

original retail purchase or lease. 
For commercial uses and applications: Cub Cadet warrants this 

product (excluding 

Normal Wear Parts

, as described below) against 

defects in material and workmanship for a period of one (1) year from 

the date of original retail purchase or lease.
“Cub Cadet” will, at its option, repair or replace, free of charge, any 

part found to be defective in materials or workmanship.  This limited 

warranty shall only apply if this product has been operated and 

maintained in accordance with the Operator’s Manual furnished with 

the product, and has not been subject to misuse, abuse, neglect, 

accident, improper maintenance, alteration, vandalism, theft, fire, 

water, or damage because of other peril or natural disaster.  Damage 

resulting from the installation or use of any part, accessory or 

attachment not approved by Cub Cadet  for use with the product(s) 

covered by this manual will void your warranty as to any resulting 

damage.

Normal Wear Parts 

are warranted to be free from defects in material 

and workmanship for a period of thirty (30) days from the date of 

purchase. Normal wear parts include, but are not limited to items 

such as: belts, skid shoes, shave plates and tires. 

HOW TO OBTAIN SERVICE: 

 Warranty service is available, WITH 

PROOF OF PURCHASE, through your local authorized service 

dealer. To locate the dealer in your area:

In the U.S.A.

To locate the dealer in your area, check your Yellow Pages, or contact 

Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or 

call 1-877-282-8684,  or log on to our Web site at www.cubcadet.

com.

In Canada

Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 

1-800-668-1238 or log on to our Web site at www.mtdcanada.

com.
This limited warranty does not provide coverage in the following 

cases:

a.  Routine maintenance items such as lubricants, filters, blade 

sharpening, tune-ups, brake adjustments, clutch adjustments, 
deck adjustments, and normal deterioration of the exterior finish 
due to use or exposure.

b.  Cub Cadet does not extend any warranty for products sold or 

exported outside of the United States and/or Canada, and their 
respective possessions and territories, except those sold through 
Cub Cadet’s authorized channels of export distribution.

c.  Replacement parts that are not genuine Cub Cadet parts.
d.  Service completed by someone other than an authorized service 

dealer.

e.  Transportation charges and service calls.
No implied warranty, including any implied warranty of mer-
chantability of fitness for a particular purpose, applies after the 
applicable period of express written warranty above as to the 
parts as identified. No other express warranty, whether written 
or oral, except as mentioned above, given by any person or 
entity, including a dealer or retailer, with respect to any product, 
shall bind Cub Cadet.  During the period of the warranty, the 
exclusive remedy is repair or replacement of the product as set 
forth above.
The provisions as set forth in this warranty provide the sole and 
exclusive remedy arising from the sale.  Cub Cadet shall not be 
liable for incidental or consequential loss or damage including, 
without limitation, expenses incurred for substitute or replace-
ment lawn care services or for rental expenses to temporarily 
replace a warranted product.
Some states do not allow the exclusion or limitation of incidental 
or consequential damages, or limitations on how long an implied 
warranty lasts, so the above exclusions or limitations may not apply 
to you.
In no event shall recovery of any kind be greater than the amount 
of the purchase price of the product sold.  

Alteration of safety 

features of the product shall void this warranty.  You assume the 
risk and liability for loss, damage, or injury to you and your property 
and/or to others and their property arising out of the misuse or 
inability to use the product.
This limited warranty shall not extend to anyone other than the 
original purchaser or to the person for whom it was purchased as a 
gift.
HOW STATE LAW RELATES TO THIS WARRANTY:  This limited 
warranty gives you specific legal rights, and you may also have other 
rights that vary in different jurisdictions.
IMPORTANT:  Owner must present Original Proof of Purchase to 
obtain warranty coverage.

    Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684

          MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238

GDOC-100160 REV. A

CUB CADET LLC

MANUFACTURER’S LIMITED WARRANTY FOR 

SNOW THROWERS 

Содержание 726 TDE

































Отзывы: