background image

WARNING! 

To prevent accidental start-up, shut off 

the engine and remove the key before performing 

any type of engine maintenance.

Periodic inspection and adjustment of the engine is essential if 

high level performance is to be maintained. Regular maintenance 

will also ensure a long service life. The required service intervals 

and the type of maintenance to be performed are described 

in the table below. Follow the hourly or calendar intervals, 

whichever occur first. More frequent service is required when 

operating in adverse conditions.

Maintenance Schedule

Changing Engine Oil

NOTE: 

Check the oil level before each use and after every five 

hours of operation to be sure correct oil level is maintained. Refer 

to Checking Oil Level in the Operation section

Drain fuel from tank by running engine until the fuel tank is 

1. 

empty. Be sure fuel fill cap is secure.
Place suitable oil collection container under oil drain plug. 

2. 

Remove oil drain plug. See Fig. 7-1.

3. 

Tip engine to drain oil into the container. Used oil must be 

4. 

disposed of at a proper collection center.
Reinstall the drain plug and washer and tighten securely. 

5. 

Oil Drain

Oil Plug

Figure 7-1

Refill with the recommended oil and check the oil level; 

6. 

refer to Operation section for instructions.

Reinstall the oil filler cap/dipstick securely.

7. 

CAUTION: 

Thoroughly wash your hands with soap 

and water as soon as possible after handling  

used oil.

NOTE: 

Please dispose of used motor oil in a manner that is 

friendly to the environment. Take it to a recycling center or other 

collection center.

Oil Recommendations

When adding oil to the engine, refer to viscosity chart below. 

Engine oil capacity is 600 ml (approx. 20 oz.). Do not over-fill. 

Use a 4-stroke, or an equivalent high detergent, premium 

quality motor oil certified to meet or exceed U.S. automobile 

manufacturer’s requirements for service classification SG, SF. 

Motor oils classified SG, SF will show this designation on the 

container.

-30º -20º -10º 0º

0º 20º 40º

-20º

5W-30

0W-30

-40º

Synthetic

CAUTION: 

DO NOT use nondetergent oil or 

2-stroke engine oil. It could shorten the engine’s 

service life.

Tasks

F

irst 5 Hrs

. Each Use or 

Ever

y 5 Hr

s.

Every Season 

or 25 Hrs.

Every Season 

or 5

0 Hr

s.

Every Season 

or 100 H

rs.

Service Dates

Check engine oil
Change engine oil
Check spark plug
Service spark plug
Clean exhaust area

Engine Maintenance

7

20

Содержание 726 TDE

































Отзывы: