Cub Cadet 726 TDE Скачать руководство пользователя страница 12

Страница: 12 / 32

Track Dri

ve Control

uger

Cont

rol Lock

Headlight

Chute Assembly

Chut

Cleanout

Auge

id Sho

Shi

Lev

Chute Dir

ectiona

l Control

Auger Control

ack Steering Control

Heate

d G

rips

ack Lock Lev

Norma

l Snow

Packed Sno

Transport

Ignition Key

l Fill

Primer

Gasoline

Cap

Electr

Starter

Outlet

Recoil S

tarter

Handle

l D

rain

Chok

Contro

Thro

Contro

Electr

Starter

tton

Figure 4-1

WARNING!

Read, understand, and follow all

instructions and warnings on the machine and in

this manual before operating.

Shift Lever

The shift lever is located in the right side of the handle panel and

is used to determine both the ground speed and direction of

travel. It can be moved into any of eight positions.

Forward

Your snow thrower has six forward (F) speeds, with position

number one (1) being the slowest.

Reverse

Your snow thrower has two reverse (R) speeds, with position

number one (1) being the slowest.

NOTE:

Always release the drive control before changing

speeds.

Headlight

The headlight is on whenever the engine is running.

Heated Grip

To activate the heated grips, move the switch found on the rear

of the dash panel into the ON position.

Skid Shoe

The space between the shave plate and the ground can be

adjusted by positioning the skid shoes. Refer to Skid Shoe

Adjustment on page 10.

Controls and Features

Содержание 726 TDE

































Результаты поиска

Содержание 726 TDE

Отзывы:

Похожие инструкции для 726 TDE

Бренды по названию

Популярные бренды

Cub Cadet 726 TDE, Руководство оператора

Результаты поиска

Содержание 726 TDE

Отзывы:

Похожие инструкции для 726 TDE

Бренды по названию

Популярные бренды