background image

MNX10030  Rev 0 

          

                             

8/20/2008  

1

 

 
 
Section I 
Overview 

Introduction.....................................................................….… 2 
Description.............................................................................. 2 
 

Section II 
Installation 

Mounting………....................................................................... 4 
Electrical Connections............................................................. 5 

 

Section III 
Operation 

Operating Procedure............................................................... 6 

 

Section IV 
Maintenance 

General.................................................................................... 8 
Warranty.................................................................................. 8 

 

Figures 

Figure 1 (Selection Guide)……………………...………………...3 
Figure 2 (Mounting Bracket Location)...................................... 4 
Figure 3 (Conduit Entry Layout).……………….……………..… 4 
Figure 4 (Grounding Enclosure)………………...…………….….5 
Figure 5 (Enclosure Wiring Locations)…………………………..6 
 

Table 

Table 1 (Specifications)………………………..………….….…. 3 

 
 
 
 
 
 
 
 
 
 
 
 

Contents 

Содержание XE150










Отзывы: