CTC Union FRM220-NMC Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 182

CTC Union FRM220-NMC Скачать руководство пользователя страница 112

Appendix A

110

E1 / T1 Line Card Detail

The following is the display screen for the E1 BNC fiber converter.

Slot #03 E1 BNC Select Menu:

Select Menu:
1: Local Setting
2: Remote Setting

Command Function Key:

'1' to '2': Select Menu
'ESC': Main Menu

The E1 / T1 card supports remote management features; Select 1 or 2.

Slot #03 E1 BNC Card Status:

E1 >> Link Up << H/W Version: 1.1
E1 AIS >> Off << F/W Version: 1.1
Fiber >> Link Up <<
Test LED >> Off <<

Card Parameter Setup Menu:

0: Channel Enable/Disable >> Enable <<
1: Far End Fault Setting >> Disable <<
2: AIS Setting >> Disable <<
3: Line Code >> HDB3 <<
4: Port Reset >> Disable <<
5: E1/T1 Loop-Back test >> Off <<
6: Fiber Loop-Back test >> Off <<
7: Reset Channel Setting to Default

Command Function Key:

'0' to '4': Toggle I/O Card Settings
'5' to '7': I/O Card Commands
'R': Refresh Status
'ESC': Previous Menu

The following are descriptions of the function keys available and the actions which they perform.

0

: This key toggles the channel enable/disable and can be used to halt transmission on this line card to the

remote cpe side.

1

: This key toggles the FEF setting enabled or not.

2

: This key toggles the AIS; normal condition should disabled.

3

: This key toggles between AMI and HDB3 (BZ8S for T1) Line coding.

4

: This key toggles the Port Reset.

5

: This key initiates the E1 remote loop back test.*

6

: This key initiates the Fiber remote loop back test.*

7

: This key will reset the card settings to factory default.

R

: This key will refresh the screen display.

ESC

: This key will leave the card setting menu.

* During loop back tests, normal traffic is interrupted.

«
...
110
111
112
113
114
...
»

Содержание FRM220-NMC























































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды