background image

Safety instructions 

DP400 mobil V1.00 EN 

Seite 4 von 15 

1.2 

   Installation 

NOTE! 

 

The plug of the power supply unit (charger) is used as a separator. 

This separator must be clearly recognisable and easily accessible by the user. A 
plug connector with a CEE7/7 system is necessary. 

NOTE! 

 

Only the supplied power supply may be used. 

1.3 

 Lithium Ion Batterie 

Warning! 

Battery! 

The replacement of the battery must only be carried out by authorised and 
skilled personnel, and when the device is de-energised. 

Only the original battery of the manufacturer with built-in protection circuit 
may be used. 

Do not use any other power supply for charging the Li-Ion battery as the provided.

Do not charge the battery under conditions that are not specified in the manual.

Do not charge the battery in an environment with flammable substances. Never charge the
battery unattended.

Transport

The contained lithium ion batteries are subject to the Dangerous Goods Legislation requirements. The user
can transport the batteries by road without further requirements.
When being transported by third parties (e.g.: air transport or forwarding agency), special requirements on
packaging and labelling must be observed. For preparation of the item being shipped, consulting an expert
for hazardous material is required.
Please also observe possibly more detailed national regulations.

    Disposal 

The datalogger, rechargeable batteries, accessories and packaging should be sorted for  
environmental friendly recycling. 
Do not dispose of power tools and batteries/rechargeable batteries into household waste! 

Only for EC countries: 

According to the European Guideline 2012/19/EU, power tools that are no longer 
usable, and according to the European Guideline 2006/66/EC, defective or used 
battery packs/batteries, must be collected separately and disposed of in an environmentally 
correct manner. 

Batteries no longer suitable for use can be directly returned at: 

CS Instruments GmbH & Co.KG 
Zindelsteiner Str. 15  
D-78052 VS-Tannheim

CS Instruments GmbH & Co.KG 
Am Oxer 28c  
D-24955 Harrislee

Содержание DP 400 mobil
















Отзывы: