Crystal Vision Indigo ADP 310 Скачать руководство пользователя | Manualshive

Страница: 33 / 49

background image

Crystal Vision

Specification

8 Specification

General

Dimensions 100mm x 266mm module with DIN 41612 connector.

Weight 200g.

Power

consumption

ADP 310 - 9 Watts.

.

Inputs

Ref Video
standards

supported

Black and Burst or tri-level sync 625/50, 525/60, 525/59.94.

Return loss 50Mhz to 1.5GHz -15dB.

Audio Digital: Up to four 24 bit stereo pairs (total of eight inputs) 48kHz

sampled. AES3 110 ohm or HiZ (balanced) D-Type, or AES3-id
(unbalanced) 75 ohm BNC.

Analogue: Up to two stereo pairs (total of four mono channels). Hi-Z
balanced.

Outputs

Audio Digital: Up to four 24 bit stereo pairs (total of eight outputs). AES: 110

ohm balanced D-Type or 75 ohm unbalanced BNC.

Analogue: Up to two stereo pairs, low-Z balanced.

Rear Module I/O

RM47

RM74

110 ohm balanced audio on a high density D-type.

Reference video Black and Burst or tri-level sync input.

75 ohm unbalanced audio on BNCs.

Reference video Black and Burst or tri-level sync input.

Audio Delay Adjustable audio delay of up to 400ms on each channel. Delay is either

on or off for any given channel.

Store presets and control via the card, frame active front panel, remote
panel and Statesman.

Audio Processing Gain level adjustment on each channel b18dB and -18dB in

0.1dB steps with 0dB calibration.

Mute.

Stereo to mono conversion.

Status monitoring

LEDs Front of card edge LED indicators to indicate:

PSU rails present.

AES Inputs present.

GPI Out 5 and 6 active.

ADP 310 User Manual R1.2

32

19 June 2019

«
...
31
32
33
34
35
...
»

Содержание Indigo ADP 310


















































Отзывы:

Нет отзывов

Похожие инструкции для Indigo ADP 310

FrameSaver 9120

Бренд: Paradyne Страницы: 2

NVIP- NVRA0104/GO

Бренд: Novus Страницы: 44

Бренд: SIIG Страницы: 20

Бренд: CNC4PC Страницы: 11

Бренд: ekwb Страницы: 11

Бренд: ZiLOG Страницы: 11

Бренд: ST Страницы: 67

PCI4-AD-x16HI-BG4

Бренд: Serial Cables Страницы: 15

Бренд: RAK Страницы: 14

Бренд: C&H Technologies Страницы: 2

Бренд: Divio Страницы: 78

Бренд: Acqiris Страницы: 89

Бренд: Actisense Страницы: 14

Бренд: Fujitsu Страницы: 36

Бренд: Fujitsu Страницы: 20

Бренд: Fujitsu Страницы: 49

Бренд: Fujitsu Страницы: 16

Бренд: Fujitsu Страницы: 121

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды