Crystal Vision Indigo ADP 310 Скачать руководство пользователя | Manualshive

Страница: 19 / 49

background image

Crystal Vision

Control and Status monitoring

5.2 Using the front control panel

At power up, the LEDs of all eight control panel keys will illuminate briefly. Once the
panel has completed its power up and configuration sequence the panel will enter its
status mode and display the current software version and frame IP address.

‘Status’ menu showing current software version and IP address

Selecting an ADP 310

To continue with control panel operation or configuration, press the ‘Device’ key once.
The control panel will display the name of the card that first responds to the polling
request together with its location number. The location number consists of the frame
number plus the card position in the frame. Rotate the Shaft control to poll through
the available cards. Use the F2 soft key to toggle between the card’s serial number
and issue number with modification level.

‘Device’ menu showing ADP 310 in slot 1.01

In the example above, the card displayed is located in the first frame in slot number 1.

When the desired card is selected press the ENTER key to access that card’s HOME
menu.

ADP 310 User Manual R1.2

18

19 June 2019

«
...
17
18
19
20
21
...
»

Содержание Indigo ADP 310


















































Отзывы:

Нет отзывов

Похожие инструкции для Indigo ADP 310

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: Usr Страницы: 2

Proventia A1204

Бренд: Internet Security Systems Страницы: 42

Бренд: XNET Страницы: 17

Бренд: Softing Страницы: 4

Бренд: MEDIATEK Страницы: 166

Бренд: Avenview Страницы: 28

Data Capture Board CLC-CAPT-PCASM

Бренд: National Semiconductor Страницы: 15

PCI-AD-x16HE-BG4

Бренд: Serial Cables Страницы: 18

Бренд: Primera Страницы: 82

Бренд: WiebeTech Страницы: 8

Wisenet XRN-6410DB4

Бренд: Hanwha Techwin Страницы: 118

Бренд: ADLINK Technology Страницы: 69

Analog Pulse Generator 812-OP/H

Бренд: Link electronics Страницы: 2

Бренд: X-Micro Страницы: 24

DAQ X NI 634 Series

Бренд: National Instruments Страницы: 278

Бренд: Axis Страницы: 10

Бренд: NetApp Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды