Crystal Vision Indigo ADP 310 Скачать руководство пользователя | Manualshive

Страница: 32 / 49

background image

Crystal Vision

Troubleshooting

7 Troubleshooting

Card edge monitoring

The front edge of the card provides useful power rail monitoring and input status.

ADP 310 front edge view

See

Card Edge Controls

for explanation of card edge LEDs.

The card edge LEDs and 10-digit display may be used in conjunction with status
information from any connected remote status panel display or from VisionWeb or
Statesman if available.

Board edge control was removed from ADP 310 in 2018. Therefore the card edge
control information is only relevant for older versions of the product.

Basic fault finding guide

The Power OK LEDs are not illuminated

Check that the frame PSU is functioning – refer to the appropriate frame manual for detailed
information

The card no longer responds to card edge or front panel control

Check that the card is seated correctly and that the Power OK LEDs are lit

Check any active control panel cabling

Check if the control panel can control another card in the same rack

If necessary reset the card

Resetting the card

If required, the card may be reset by removing the card from the rack and then re-inserting it

It is safe to re-insert the card whilst the rack is powered. Any previous configuration will be
retained, use a factory reset to erase any configurations stored in the card.

ADP 310 User Manual R1.2

31

19 June 2019

«
...
30
31
32
33
34
...
»

Содержание Indigo ADP 310


















































Отзывы:

Нет отзывов

Похожие инструкции для Indigo ADP 310

Professional Series

Бренд: PACOM Страницы: 15

Бренд: Javad Страницы: 35

F-Tile SDI II Intel Agilex

Бренд: Intel Страницы: 39

Бренд: Caton Страницы: 18

Бренд: AXIOMTEK Страницы: 2

Advanced Flame 1.0

Бренд: Eastern Voltage Research Страницы: 12

Бренд: ADTRAN Страницы: 9

Бренд: Extron electronics Страницы: 19

Бренд: ActiveEye Страницы: 35

Бренд: Cooler Master Страницы: 4

Бренд: R.V.R. Elettronica Страницы: 171

RJModem MT5656RJ

Бренд: Multi-Tech Страницы: 27

Бренд: National Instruments Страницы: 45

Бренд: Inter-m Страницы: 20

Suppression Inductors LFZ24H

Бренд: Delta Electronics Страницы: 1

Бренд: Alphacool Страницы: 3

Бренд: IEI Technology Страницы: 213

CORIOview MWP Series

Бренд: Tvone Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды