Crown DriveCore I-Tech 4x3500B HD Скачать руководство пользователя страница 6

Страница: 6 / 72

Operation Manual

I-Tech HD DriveCore Series

Power Amplifiers

page 6

2.1 Unpack and Install Your

Amplifier

Please unpack and inspect your amplifier for

any damage that may have occurred during

transit. If damage is found, notify the

transpor tation company immediately. Only you

can ini tiate a claim for shipping damage. Crown

will be happy to help as needed. Save the

shipping carton as evidence of damage for the

shipper’s inspection.
We also recommend that you save all packing

materials so you will have them if you ever need

to transport the unit.

Never ship the unit

without the factory pack.

YOU WILL NEED (not supplied):
•  Input wiring cables
•  Output wiring cables
•  Ethernet cables
•      Rack for mounting amplifier (or a stable

surface for stacking)

WARNiNg: Before you start to set up

your amplifier, make sure you read and

observe the important Safety instruc-

tions found at the beginning of this

manual.

cAUTiON: Before you begin, make sure

your amplifier is disconnected from the

power source, with the power switch in

the “off” position and all level controls

turned completely down (counterclock-

wise).

Use a standard 19-inch (48.3 cm)

equipment rack (EIA RS-310B). See

Figure 2.1 for ampli fier dimensions.
You may also stack amps without using a

rack.
NOTE: When transporting, amplifiers should be

supported at both front and back.

When using an equipment rack, mount units

directly on top of each other. Close any open

spaces in rack with blank panels. DO NOT block

front or rear air vents. The side walls of the rack

should be a minimum of two inches (5.1 cm)

away from the amplifier sides, and the back of

the rack should be a minimum of four inches

(10.2 cm) from the amplifier back panel.

Figure 2.2 illustrates standard amplifier airflow.

2 Setup

Figure 2.2 Airflow

Figure 2.1

Dimensions

MAGNETIC FIELD

CAUTION! Do not locate sensitive high-gain

equipment such as preamplifiers or tape decks

directly above or below the unit. Because this

amplifier has a high power density, it has a

strong magnetic field which can induce hum

into unshielded devices that are located nearby.

The field is strongest on the right side and right

bottom of the amplifier (facing the amplifier).

If an equipment rack is used, we recommend
locating sensitive equipment at least 20 cm
(8 inches) away from the amplifier.

1.5 In.

3.8 cm

3.5 In.

8.9 cm

16.95 In.

43.1 cm

48.3 cm

19 In.

Содержание DriveCore I-Tech 4x3500B HD









































































Результаты поиска

Содержание DriveCore I-Tech 4x3500B HD

Отзывы:

Похожие инструкции для DriveCore I-Tech 4x3500B HD

Бренды по названию

Популярные бренды

Crown DriveCore I-Tech 4x3500B HD, Руководство по эксплуатации

Результаты поиска

Содержание DriveCore I-Tech 4x3500B HD

Отзывы:

Похожие инструкции для DriveCore I-Tech 4x3500B HD

Бренды по названию

Популярные бренды