Crown DriveCore I-Tech 4x3500B HD Скачать руководство пользователя страница 56

Страница: 56 / 72

Operation Manual

I-Tech HD DriveCore Series

Power Amplifiers

page 56

13 LevelMAX

Limiter Suite

The I-Tech HD LevelMAX™ Limiter Suite features three types of limiting:

•

Peak

•

RMS

•

Transducer Thermal

and three modes of operation:

•

Auto

•

Advanced

•

Manual (OEM Factory Locked)

The standard i-Tech HD LevelMAX limiter panel (Advanced Mode) is shown

below:

LevelMAX has been designed to limit accurately to the specified voltage

thresholds. The addition of a thermal limiter allows thresholds for the

faster-acting RMS and peak limiters to be set higher, providing more output

and maintaining dynamic range before the onset of limiting, while protecting

the long term integrity of the transducers.

In Auto or Advanced modes, turning on the LevelMAX Limiter Suite will

enable all three limiters: Peak, RMS and Thermal.

The three LevelMAX limiter types and operating modes are outlined in the

following sections.

Содержание DriveCore I-Tech 4x3500B HD









































































Результаты поиска

Содержание DriveCore I-Tech 4x3500B HD

Отзывы:

Похожие инструкции для DriveCore I-Tech 4x3500B HD

Бренды по названию

Популярные бренды

Crown DriveCore I-Tech 4x3500B HD, Руководство по эксплуатации

Результаты поиска

Содержание DriveCore I-Tech 4x3500B HD

Отзывы:

Похожие инструкции для DriveCore I-Tech 4x3500B HD

Бренды по названию

Популярные бренды