background image

Assembly

ManChester Fun DeCk

19807-100 rev D (07-16)

© Copyright 2011, Creative Playthings

Page 3

sAFe PlAy AreA

selectInG the cOrrect lOcAtIOn FOr yOur PlAy PrODuct Is ImPOrtAnt FOr 

yOur chIlDren’s sAFety AnD the PrODuct’s lOnGeVIty.

Play set Dimensions:

 •  the manchester Fun Deck Assembly has ground dimensions of 7'-0" x 5’-0"
 •  the manchester Fun Deck Play set Accessory adds 7'-0" to the safe Play Area at the end of your gym.
 •  Additional accessories may increase the size of the safe Play Area.
 •  the maximum fall height for your manchester Fun Deck is 120" as measured from the top of the Wall supports.

safe Play Area:

 •  the safe Play Area refers to a zone extending 6' beyond the Play set on all sides, including the slide and the 

space above the Play set. because children may deliberately jump from a moving swing, the safe Play Area 

must be extended to 14 in front of and behind a swinging Accessory.

 •  the ground surface must be level. Installing your Play set on sloping ground can cause it to lean or “rack". this 

leaning puts additional stress on all connections and joints and in time will cause those connections to loosen 

and fail.

 •  the safe Play Area must be free of all structures, landscaping, trees and branches, rocks, wires, and other 

obstacles to safe play. children can be seriously injured running, or swinging into these obstacles.

 •  remove all tripping hazards from the safe Play Area. tripping hazards include; roots, stumps, rocks, landscap-

ing, sprinkler heads, railroad ties, plumbing and electrical connections.

 •  Do not install your Play set over concrete, gravel, asphalt, packed earth, or any other hard surface. the follow-

ing is a list of recommended ground covers from the consumer Product safety commission.

reCoMMenDeD GrounD Cover

suggested Material 

uncompressed Depth

Double shredded Bark Mulch 

9"

uniform Wood Chips 

12"

Fine Gravel 

12"

Fine sand 

12"

 •  Any edging used to contain the ground cover must be beyond the safe Play Area. (i.e.. landscape timbers)

A FAll OntO A hArD surFAce cOulD result In serIOus 

Injury.

6'

6'

6'

14'

14'

WHICHEVER

IS GREATER

safe play area using

recommended ground cover.

Landscape timbers 6' from 

play structure.

Содержание Manchester Fun Deck





















Отзывы: