Creative Playthings 63091-111 Скачать руководство пользователя страница 11

Страница: 11 / 11

DiRECT ADAPTER FOR SPiRAL & SWOOSH SLiDES

19946-100 Rev B (07-17)

page 11

Assembly instructions

91-1/2"

Gym Brace

1" dia. counter-bore 1/2"

deep and 3/8" dia. thru. drill

Determine side for

counter-bore before

drilling.

step 2 — cut and Drill the Gym brace

Use a saw to cut the Gym Brace to 91-1/2". Be careful to cut off the square-cut end. Place the off-cut piece even with the

cut end of the board and mark the hole positions on the Gym Brace. See the illustration above.
Hold the Gym Brace in place to determine the side where a counter-bore is needed. On the side requiring a counter-bore,

drill 1" diameter holes 1/2" deep at the marks. At the center of the 1" holes, drill 3/8" diameter holes completely through board.

step 3 — finish beam Assembly

Use the instructions included with the Swing Beam to

complete the installation using the altered parts

Содержание 63091-111












Результаты поиска

Содержание 63091-111

Отзывы:

Похожие инструкции для 63091-111

Бренды по названию

Популярные бренды

Creative Playthings 63091-111, Инструкция по сборке

Результаты поиска

Содержание 63091-111

Отзывы:

Похожие инструкции для 63091-111

Бренды по названию

Популярные бренды