www.cls-led.com
- 16 -
- 15 -
CLS Dennis RGB Wallwasher
tHE EVEnt ScHEduLEr
Scheduler is a menu that allows to organize a series of 48 events over a period of a week and which is
repeated week after week. Each event can control the day and time of the start and finish of one of the ten
programs already prepared on board the CLS Dennis RGB Wallwasher, in order to automate playback, without
the need for any external operators.
Step 1 - choosing the event number
1. Use the
uP/doWn
keys to find the “
ScHEdL
” menu.
2. Press “
Enter
” for a few seconds, until the following appears: “
EVEnt
”.
3. If it is necessary to create a event other than number 1, press “
Enter
” again and “
**
” will begin to flash.
4. Use the
uP/doWn
keys to choose the required event, from 1 to 48, then Press “
Enter
” to exit the
EVEnt
menu and confirm.
Step 2 - choosing the program number
1. Use the “
uP
” key to pass to the “
ProG
.” menu.
2. Press “
Enter
” and “
*
” will begin to flash.
3. Use the
uP/doWn
keys to choose the required program number (from 1 to 5) to be controlled by scheduler.
4. Press “
Enter
” to exit the
ProG
. menu and confirm.
Step 3 - choosing the day
1. Use the “
uP
” key to pass to the “
dAY
” menu.
2. Press “
Enter
” and “
***
” will begin to flash.
3. Use the
uP/doWn
keys to choose the day of the week which the event must begin. The days of the
week are expressed as follows:
• ALL Every day
• TUE Tuesday
• THU Thursday
• SAT Saturday
• MON Monday
• WED Wednesday
• FRI Friday
• SUN Sunday
4. Press “
Enter
” to exit the
dAY
menu and confirm.
Step 4 - Start time
START TIME is used to configure: the hour, minutes and seconds in which an event containing
a previously prepared program will start.
1. Use the “UP” key to select the “START” menu.
2. Press “Enter” and “
**
”:** will begin to flash.
3. Use the UP/DOWN keys to choose the hour when the program has to start (from 0 to 23).
4. Press “Enter” to select the minutes.
5. Use the UP/DOWN keys to choose the minutes when the program has to start (from 0 to 59).
6. Press “Enter” to exit the “START” menu and confirm.
!
W
AR
NI
NG
ATTENTION!
BEfORE pROcEEDING wITh ThE pROGRAMMING Of ThE SchEDuLER,
IT IS IMpORTANT TO SET ThE cuRRENT DATE AND TIME (SEE chAp.
MENu - pARAGRAph: DAyS Of ThE wEEk AND TIME)
Step 5 - End time
END TIME is used to configure: the hour, minutes and seconds in which an event containing a previously
prepared program will end.
1. Use the “
uP
” key to select the “
End
” menu.
2. Press “
Enter
” and “
**
”:
**
will begin to flash.
3. Use the
uP/doWn
keys to choose the hour at which the program has to end (from 0 to 23).
4. Press “
Enter
” to select the minutes.
5. Use the
uP/doWn
keys to choose the minutes at which the program has to end (from 0 to 59).
6. Press “
Enter
” to exit the “
End
” menu and confirm.
Step 6 - Enabling an event
1. Use the “
uP
” key to select the “
EnABLE
” menu.
2. Press “
Enter
” and “
***
” will begin to flash.
3. Use the
uP/doWn
keys to choose
on
to enable the event, or
oFF
if it is to be disabled.
4. Press “
Enter
” to exit the “
EnABLE
” menu and confirm.
Repeat the above steps to program other events on the CLS Dennis RGB Wallwasher. Once programming is
finished, keep “
Enter
” pressed down for approx. 6 seconds in order to exit the
ScHEdL
menu.
Step 7 - Enabling the scheduler
To start the scheduler and all its “Actions”, it is necessary to enter the
ScHEd.
menu.
1. Use the UP/DOWN keys to find the “
ScHEd
.” menu.
2. Press “
Enter
” and “
***
” will immediately begin to flash.
3. Use the
uP/doWn
keys to choose
on
or
oFF
, according to requirements.
4. Press “
Enter
” to exit the
ScHEd.
menu and confirm.
2007 CLS-LED BV. All rights reserved. Information subject to change without notice, CLS-LED BV and all affiliated companies
disclaim liability for injury, damage direct or indirect loss, consequential or economic loss or any other loss occasioned by the
use of, inability to use or reliance on the information contained in this manual. No part of this manual may be reproduced,
in any form or by any means, without permission in writing from CLS-LED BV. Other legal information can be found in our
General conditions to be found on the back of your CLS-LED BV invoice or on our website www.cls-led.com/Conditions
tEcHnIcAL SPEcIFIcAtIonS
The head can be moved in relation to the base:
PAN +/- 45° and TILT -75° / +15° can be locked in the desired position.
Voltage:
200~240 VAC
Power consumption:
160 VA max.
LEDs:
24 x red, 18 x green and 7 x blue LEDs
IP rating:
IP65
Measurements:
410 x 427 x 232 mm (w x h x d)
Weight:
13,5 kg
Shipping weight:
18,2 kg
