CreatBot F430, Руководство пользователя

Страница: 39 / 43

- 39 -
Frequently Asked Questions
not over 120℃, and you can close the bed above 100mm except printing ABS
or other high-temperature required filaments.
3 . The model not stick on the platform ?
Please paste masking paper or Kapton tape on the platform , or the nozzle is
too far away from the platform, or the bottom of the model is not leveled.
4 . No or less silk coming on the first layer ?
The distance between nozzle and platform is too small , or the filament has not
been sent to the nozzle .
5. Why nozzle is not spit silk ?
The filament is not pressed or too tight, or print temperature is too low, or the
filament feeder not working.
6 . How to prevent model become warped ?
Increase hot bed temperature or use Kapton, or change platform adhesion
type to Raft, or cover the baffle, or reduce indoor ventilation.
7 . How far from nozzle to platform appropriate ?
Distance should be 0 in theory , but there is no absolutely flat platform, so the
distance -0.1mm. Finally, with the actual printing effect as the
standard, too close will lead to a silk blocked, too far will cause the model not
stick on the platform.
8 . How to determine whether the
temperature
is too high ?
PLA temperature is too high will appear liquefaction , ABS will be the carbide ,
that will block the nozzle .
9 . What reasons will causing nozzle blocked ?
Filament are impurities or print environment dust too much, bad of thermal
conductivity between the nozzle and the heating block.
10 . Model surface is loose with crack ?
The layer is too high or the printing speed too fast, nozzle temperature too
low or filament press nut too loose, or filament is blocked.
11 . How to print a small model ?
Multiple the model , and print them at a time.
12 . Dual color model not aligned ?
Adjust offset of second nozzle in machine settings .
13 . Dual color model color interference ?
Align two nozzle in vertical direction
14 . There is too much silk drag on the model ?
Please enable filament retraction, and specified proper retract speed, and
distance, the retract distance should not less than 2mm, and the speed not
less than 30mm/s.
Printing Troubleshoot
Frequently Asked Questions
Hardware Troubleshoot
1. Display " MINTEMP " ?
The environment is too low, or temperature sensor is damaged, please keep
the room temperature above 0 ℃ .
2. Display " MAXTEMP " ?
Temperature of nozzle or bed too high , or temperature sensor is damaged ,
please keep their temperature in a suitable range.
3 . USB connection problems ?
Please specify the correct port and baud rate (250000) , or change a shorter
USB cable .
4 . Nozzle heats up too slowly ?
Temperature in door is too low , or use a fan duct , or turn up output voltage
( 24 . 5v ).
5 . Print head stuck ?
Clean the guide rail and add lubricating oil .
6. Print head can not move ?
Stepper motor chipset burned , or belt damaged, or belt wheel screw loose.
7 . Print head hit the framework ?
Corresponding axis stop limit or circuit fault .
8 . Unable to power on ?
Power switch is damaged or fuse is burned, and please check whether the
power adapter is working properly
or power check board is damaged .
Printing Troubleshoot
1. How to set the temperature of the nozzle ?
Different filament temperature is different , general as follows :
PLA temperature 190 ℃ ~ 210 ℃ ,bed 45-60 ℃
ABS temperature 230 ℃ ~ 250 ℃ ,bed 80-100 ℃
You must leave enough time for filament heating , so the faster printing speed
need the higher temperature , 60mm / s temperature need raise about 10 ℃. In
the same way , larger thickness need higher temperature .
2 . How to set the temperature of the hot bed ?
The main purpose of the hot bed is to prevent model wrapped, PLA need
about 45 ℃ and 70℃ for ABS is enough , but due to the environment and
filament , we often need to increase the temperature , the highest temperature
not over 120℃, and you can close the bed above 100mm .
- 38 -