background image

9

E-3.2) Reassembly:
Outer Seal -

 Clean and oil seal cavities in seal plate 

(10). Lightly oil 

(DO NOT use grease)

 outer surface of 

stationary member (12a). Press stationary member (12a) 
fi rmly into seal plate (10), using a seal pusher (see parts 
list- seal tool kit). Nothing but the seal pusher is to come 
in contact with seal face (see Fig. 6). 

IMPORTANT ! - DO NOT hammer on the seal 
pusher- it will damage the seal face.

Make sure the stationary member is in straight. Slide a 
bullet (see parts list-seal tool kit) over motor shaft. Lightly 
oil 

(DO NOT use grease)

 shaft, bullet and inner surface 

of bellows on rotating member (12b) (see Fig. 7). With 
lapped surface of rotating member (12b) facing inward 
toward stationary member (12a), slide rotating member 
(12b) over bullet and onto shaft, using seal pusher, until 
lapped faces of (12a) and (12b) are together (see Fig. 5).

IMPORTANT! - It is extremely important to 
keep seal faces clean during assembly. Dirt 
particles lodged between these faces will 
cause the seal to leak.

Place spring (12c) over shaft and in place on rotating 
member (12b), making sure it is seated on retainer and 
not cocked or resting on bellows tail. Slide retaining ring 
(12d) over shaft and let rest on spring (12c). Assemble 
impeller, cutter and volute as outlined in paragraph E-2.2. 
Replace oil as outlined in paragraph E-1.3.

E-4) Motor, Bearing & Inner Seal Service
E-4.1) Disassembly and Inspection:

To examine or replace the motor (1), bearings (8), (3) & 
(39) and Inner Seal (5), disassemble volute and impeller 
as outlined in paragraph E-2.1 and disassemble outer 
shaft seal as outlined in paragraph E-2.1 Drain oil from 
motor and seal cavity as outlined in paragraph E-1.3.

Remove motor fan shroud (1A), fan (1B), and motor end 
bell, by removing four motor bolts. Next remove washer 
(37), shims (36) and bearing (8) from motor (1). Exam-
ine upper bearing (8) and replace if required. Lift motor 
stator from motor rotor and then Lift motor stator from 
intermediate coupling (6). To remove ball bearing (3), 
remove retaining ring (7) from intermediate coupling (6) 
and pull motor shaft, ball bearing (3) and inner seal (5) 
from intermediate coupling (6).

FIGURE 4

FIGURE 5

Stationary Member (12A) & 
(5A) Polished Face Out

Seal Plate (10) or
Intermediate (6)

Seal Pusher

FIGURE 6

FIGURE 7

Rotating Member 
(12b) & (5B)

Seal Pusher

Motor & 
Intermediate

Bullet

MOTOR END

(INBOARD END)

PUMP END

(OUTBOARD END)

MOTOR END

(INBOARD END)

PUMP END

(OUTBOARD END)

Seal Plate (10)
Intermediate (6)

Retaining Ring (5d)

Stationary (12a)

Rotating Member 
(12b)

Retaining Ring (12d)

Spring (12c)

SEAL ASSEMBLY

 (12)

Spring (12c)

Rotating Member 
(5d)

Stationary (5a)

SEAL ASSEMBLY

 (5)

Содержание DGV2042





















Отзывы: