Crane Electronics TCI Multi Скачать руководство пользователя страница 3

Страница: 3 / 32

Manufacturer:

Crane Electronics Ltd

Address:

3 Watling Drive

Sketchley Meadows

Hinckley

Leicestershire

LE10 3EY

Tel:

+44 (0)1455 25 14 88

Crane Electronics Limited declares that the TCI Multi has been assessed and complies with the UK regulatory

requirements.

Crane Electronics Limited declares that the TCI Multi has been assessed and complies with the requirements of

the relevant CE Directives.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

particular installations. If this equipment does cause harmful interference to radio or television reception

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

ADDRESS

COMPLIANCE

UKCA MARKING

CE MARKING

Содержание TCI Multi

































Результаты поиска

Содержание TCI Multi

Отзывы:

Похожие инструкции для TCI Multi

Бренды по названию

Популярные бренды

Crane Electronics TCI Multi, Руководство оператора

Результаты поиска

Содержание TCI Multi

Отзывы:

Похожие инструкции для TCI Multi

Бренды по названию

Популярные бренды