Craftsman CM4.33 Скачать руководство пользователя

Страница: 4 / 48

Title part xxx

Subtitle part xxx

craftsman marine diesel engines CM4.33 / cm4.42

Preface

Dear owner of this engine,

We should like to thank you very much indeed for your

decision to procure a marine diesel engine, made by

Craftsman Marine.

Provided you will make proper use of it and take care of

adequate maintenance, this engine will serve you faith-

fully and trouble-free, for many years to come.

This instruction manual informs you about the control,

the maintenance and the inspection of the Craftsman

Marine diesel engines, models CM4.33 and CM4.42.

Please store this manual in an accessible place.

Should you have any further questions after having read

this manual, we shall be delighted to be of service.

Craftsman Marine B.V.

Note:

This manual applies to model CM4.33 and model CM4.42. Therefore, it can happen that a drawing

or picture is not always an exact referral to the engine that you have purchased. Please read this

manual carefully before commissioning the engine.

Improper use of this engine may cause accidents and all warranty conditions may become invalid.

In this manual you will also find detailed instructions of how and how regularly the various com-

ponents of your engine must be serviced. This engine must be used exclusively in accordance with

the prescription given in the General Conditions of Sale and Supply.

In the case of deviating use the manufacturer does not accept any responsibility whatsoever for

resulting damage. This type of risk is to be borne exclusively by the user.

Correct and proper use also implies strictly adhering to the prescriptions of operation, mainte-

nance and repair.

Only such persons, who are acquainted with the operation, the maintenance and the repair of

your engine, and who are fully aware of any danger involved, should be allowed to work at your

engine.

For that reason, always have your engine serviced, maintained and repaired by an authorized

CRAFTSMAN MARINE dealer.

In the case of modifications of the engine, which have not been previously approved by Craftsman

Marine in writing, the responsibility of the manufacturer for any resulting damage is immediately

rendered null and void.

Modifications of the injection and distribution system also form part of the aforementioned exclu-

sion of the manufacturer’s warranty.

Moreover, they may affect the performance of the engine and the exhaust gas emission in a

negative fashion.

It may be possible that the fulfillment of the legal prescriptions regarding the emission of exhaust

gases, aiming at the protection of the environment, is no longer guaranteed in that case.

Содержание CM4.33

















































Результаты поиска

Содержание CM4.33

Отзывы:

Похожие инструкции для CM4.33

Бренды по названию

Популярные бренды

Craftsman CM4.33, Руководство пользователя

Результаты поиска

Содержание CM4.33

Отзывы:

Похожие инструкции для CM4.33

Бренды по названию

Популярные бренды