Craftsman CM4.33 Скачать руководство пользователя

Страница: 36 / 48

Title part xxx

Subtitle part xxx

craftsman marine diesel engines CM4.33 / cm4.42

14 Problems and solutions

Problem

Probable cause

Solution

Starter motor does neither
rotate nor engage

• Defective or discharged battery

• Burnt fuse

• Loose or corroded connections in the starter circuit

• Defective starter switch or relay

• Defective starter motor or pinion does not engage

• Starter relay not activated owing to insufficient voltage, on account of a

too long cable from engine to instrument panel

•

Jammed components

• Check battery/charge or replace and check

alternator for proper functioning

• Replace

• Clean and tighten the connections

• Replace defective component

• Replace starter motor Fit an auxiliary starter

relay

•

Repair

Starter motor turns round,
but engine does not res-
pond

• Fuel valve closed

• Empty fuel tank

• Air in fuel system

• Fuel filter clogged up by water or dirt

• Leak in fuel supply or fuel injection line(s)

• Defective injector / injection pump

• Breather line of fuel tank clogged up

• Clogging in exhaust line

• Electrical fuel lift pump defective

• Dirt in press or suction valves of the electric fuel lift pump

• Filter of electrical fuel lift pump is clogged up.

•

Open

•

Fill

•

Check /breathe

•

Check/replace

•

Check/replace

•

Check and replace if necessary

•

Check/clean

•

Check

•

Check/clean

•

Replace. Moreover, position a water separator/

fuel filter into the fuel line between tank and

engine.

•

Check/clean

Starter motor turns round,
but engine does not res-
pond; smoke comes from
exhaust

• Air in the fuel system

• Defective injector/injection pump

• Setting of stop valve incorrect

• Defective glow plugs

• Incorrect valve tolerance

• After engine overhaul, incorrect injection moment

• Insufficient combustion air

• Poor fuel quality or polluted fuel

• Incorrect SAE-specification or quality of lubricant

• Check / bleed the system

• Check / replace if necessary

• Check / readjust

• Check / replace

• Read just

• Check / readjust

• Check air intaker and remove blockage

• Check fuel quality. Drain fuel tank and rinse it

well. Fill with good quality fuel

• Replace by good quality lubrication oil

Содержание CM4.33

















































Результаты поиска

Содержание CM4.33

Отзывы:

Похожие инструкции для CM4.33

Бренды по названию

Популярные бренды

Craftsman CM4.33, Руководство пользователя

Результаты поиска

Содержание CM4.33

Отзывы:

Похожие инструкции для CM4.33

Бренды по названию

Популярные бренды