Craftsman CM4.33 Скачать руководство пользователя

Страница: 37 / 48

Title part xxx

Subtitle part xxx

craftsman marine diesel engines CM4.33 / cm4.42

Problem

Probable cause

Solution

Engine starts running but
with irregular cycles or it
stops again

• Empty fuel tank

• Air in the fuel system

• Fuel filter clogged up with water and/or dirt

• Leaking fuel supply or fuel injection line

• Defective injector/injection pump

• Breather line of fuel tank clogged up

• Fuel line clogged

• Incorrect valve clearance

• Idling revolutions too low

• Exhaust clogged up

• Poor fuel quality or polluted fuel

• Filter of electrical fuel lift pump is clogged

• Fill it

• Check / bleed the system

• Check / clean or replace

• Check and replace, if necessary

• Check and clean or replace

• Check /remove blockage

• Check / remove blockage

• Readjust

• Check / remove blockage

• Check fuel quality.

Drain fuel tank and rinse it well.

Fill with good quality fuel

• Check / clean

Engine does not arrive
at maximum revolutions
under full load

• Air in the fuel system

• Fuel filter clogged up with water and/or dirt

• Leakage in fuel supply line or fuel injection line

• Setting of stop valve incorrect

• Oil level too high

• Incorrect SAE-specification or quality of lubrication oil

• Incorrect valve clearance

• Clogging in the exhaust

• Insufficient quantity of combusition air

• Poor fuel quality or polluted fuel

• Incorrect injection moment

• Leakage of air intake manifold

• Engine overload

• Check and bleed the system

• Clean or replace

• Check and replace, if necessary

• Check / reset

• Drain suffcient oil quantity

• Replace by engine lubrication oil of good

quality

• Adjust

• Check / remove clogging

• Check air inlet and ventilation openings in

engine room

• Check fuel quality.

Drain fuel tank and rinse it well. Fill with good

quality fuel

• Check / readjust

• Replace manifold

• Check dimensions of boat propeller

Problems and solutions 14

Содержание CM4.33

















































Результаты поиска

Содержание CM4.33

Отзывы:

Похожие инструкции для CM4.33

Бренды по названию

Популярные бренды

Craftsman CM4.33, Руководство пользователя

Результаты поиска

Содержание CM4.33

Отзывы:

Похожие инструкции для CM4.33

Бренды по названию

Популярные бренды