Craftsman 108.27807 страница 65 Скачать руководство пользователя | Manualshive

Страница: 65 / 80

background image

65

NOTE:

Since this is a rear brake only, it will not be as effective as the hand brake,

which brakes all 4 wheels simultaneously.

Carburetor/ Engine Idle RPM Adjustment

If the engine idle speed is not satisfactory, and all other conditions are favorable,
the carburetor can be adjusted as follows:

1. Warm up the engine by running

the vehicle approximately five
minutes.

2. Place the transmission in gear

with the parking brake applied.

3. Adjust the carburetor idle screw

(3) in or out until the desired idle
RPM is reached. Turning the
screw in (clockwise) will raise
RPM. Turning the screw out
(counterclockwise) will lower
RPM.

Note:

The standard idle

RPM is 1500±10%

Throttle Cable Free-Play Adjustment

Throttle cable free play is adjusted at the handlebar.
1.  Slide the boots off inline cable adjuster; loosen adjuster locknut.
2.  Turn adjuster until 1/16˝ to 1/8˝ (2 to 3mm) free-play is achieved at thumb

throttle lever.

Note:

While adjusting free-play, it is important you flip the

throttle lever back and forth.

3. Tighten locknut and slide boots over cable adjuster.

Throttle Lever

«
...
63
64
65
66
67
...
»

Содержание 108.27807

















































































Отзывы:

Нет отзывов

Похожие инструкции для 108.27807

Бренд: KAYO MOTO Страницы: 9

Бренд: Yamaha Страницы: 176

Бренд: Neilsen Страницы: 12

Sportsman Forest 550

Бренд: Polaris Страницы: 146

Бренд: Taylor-Dunn Страницы: 166

Бренд: Irbis Страницы: 99

Бренд: Polaris Страницы: 174

Бренд: Dcm Страницы: 14

Бренд: Bosch Страницы: 2

Бренд: Baja motorsports Страницы: 69

Бренд: Can-Am Страницы: 140

Бренд: Land Pride Страницы: 96

Бренд: Taxa Outdoors Страницы: 5

Бренд: Gatekeeper Systems Страницы: 60

Бренд: American Sportworks Страницы: 13

Бренд: Pongratz Страницы: 11

Бренд: Taylor-Dunn Страницы: 130

Бренд: Verhagen Leiden Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды