Craftsman 108.27807 Скачать руководство пользователя

Страница: 74 / 80

prevent condensation, and may promote corrosion and oxidation.

CAUTION:

Never cover ATV with engine and exhaust areas still warm.

19. Troubleshooting

NOTE:

The following table does not cover all the possible causes of trouble. It

should be helpful, however, as a general guide to troubleshooting. Where
applicable refer to the relative procedure in this manual for inspection, adjustment
and replacement of parts. Otherwise,

contact 1-800-643-7332 for the name of

an authorized service center to perform adjustment and replacement.

PROBLEM

CAUSE

CORRECTION

Engine runs but
ATV does not
move

1. Worn out clutch.
2. Worn/slipping belt.

1. Contact 1-800-643-7332.
2. Contact 1-800-643-7332.

Hard to start

1.  Dirty air filter.
2.  Faulty spark plug.
3.  Weak/dead battery.

4. Stale or dirty fuel.

5. Carburetor out of

adjustment.

6. Loose or damaged

wiring.

7. Engine valves out of

adjustment.

1.  Clean/replace air filter.
2.  Clean/replace spark plug.
3.  Recharge or replace

battery.

4. Empty fuel tank and refill

tank with fresh, clean fuel.

5. Contact 1-800-643-7332.

6. Check all wiring or contact

1-800-643-7332.

7. Contact 1-800-643-7332.

Will not start

1. Out of fuel.
2. Fuel tank valve not

turned to “ON”.

3. Engine Stop switch

not set to “Run”.

4. Faulty Engine Stop

switch.

5. Brake lever not

depressed.

6. Weak/dead battery.

7. Engine flooded.

8. Faulty spark plug.
9. Spark plug wire

loose.

10. Faulty starter relay.

1. Fill fuel tank.
2. Turn fuel tank valve to “ON”

position.

3. Set the Engine

Stop Switch to “Run”.

4. Contact 1-800-643-7332.

5. Depress brake lever.

6. Recharge or replace

battery.

7. Wait several minutes before

attempting to start.

8. Clean/replace spark plug.
9. Connect spark plug wire.

10. Contact 1-800-643-7332.

Содержание 108.27807

















































































Результаты поиска

Содержание 108.27807

Отзывы:

Похожие инструкции для 108.27807

Бренды по названию

Популярные бренды

Craftsman 108.27807, Руководство оператора

Результаты поиска

Содержание 108.27807

Отзывы:

Похожие инструкции для 108.27807

Бренды по названию

Популярные бренды