manualshive.com logo in svg

Craftsman 108.27807, Руководство оператора

Поделиться
Скачать
Craftsman 108.27807 Скачать руководство пользователя страница 67

 

67 

 

1.  Place vehicle on a level surface. 
2.  Run engine for two or three minutes until warm; stop engine. 
3.  Clean area around drain plug. 
4.  Place a drain pan beneath engine crankcase and remove drain plug. 
5.  Allow oil to drain completely. 
6.  Replace sealing washer O-ring of drain plug. 
7.  Reinstall drain plug and torque to 14 ft.Ibs (19N.m). 

 

Radiator Coolant Level Inspection 

Never remove the pressure cap when the engine is warm or hot. Escaping steam 
can cause severe burns. The engine must be cool before removing the pressure 
cap. 
 
To ensure that the coolant maintains its ability to protect the engine, it is 
recommended that the system be completely drained every two years and a fresh 
50/50 mixture of antifreeze and water be added. It is also necessary to inspect the 
level of coolant in the radiator if the recovery bottle has run dry.  

To add coolant, make sure the engine is cool, remove radiator pressure cap, and 
using a funnel, slowly add coolant mixture as necessary through the radiator filler 
neck.

 

NOTE: 

Use of a non-standard pressure cap will not allow the recovery system to 

function properly. If the cap should need replacement contact 1-800-643-7332 for 
the correct replacement part.

 

 

Transmission Oil Check 

The transmission fill plug (1) is located 
on the right side of the machine. The 
transmission lubricant level should be 
checked monthly or 20 hours, 
whichever comes first. Transmission oil 
should be changed annually. With the 
ATV on a level surface, remove fill plug 
and check the lubricant level. The 
correct transmission lubricant to use is 
SEA 80W/90 GL5 Lubricant. For the 
correct fluid level see section 17 
“Maintenance – Lubrication Recommendations”. 

 

Transmission Oil Changing Procedure

 

1.  Remove the four screws on the foot well and gently pull outward for access to 

WARNING

 

Содержание 108.27807

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды