Craftsman 108.27807 Скачать руководство пользователя

Страница: 76 / 80

PROBLEM

CAUSE

CORRECTION

Poor speed
performance
(Continued)

9. Loose or damaged

wiring.

10. Carburetor out of

adjustment.

11. Engine valves out of

adjustment.

filter, refill with fresh fuel.

9. Contact 1-800-643-7332.

10. Contact 1-800-643-7332.

11. Contact 1-800-643-7332.

Over heating or
over cooling

1. Incorrect coolant

level.

2.  Faulty thermo switch.
3.  Faulty thermostat.
4.  Inoperative fan

motor.

5. Faulty radiator/

radiator cap.

6. Faulty water pump.

1. Check coolant level, fill as

necessary.

2.  Contact 1-800-643-7332.
3.  Contact 1-800-643-7332.
4.  Contact 1-800-643-7332.

5. Contact 1-800-643-7332.

6. Contact 1-800-643-7332.

Belt Burning

1. Use of high range

when starting out on
an incline.

2. Insufficient ATV

warm-up.

3. Towing or carrying

loads in high range.

4. Getting ATV stuck in

mud or snow or
climbing over large
objects from a
stopped position.

1. When starting out on incline

put ATV in low range.

2. Warm up ATV for at least 5

minutes, then with
trans-mission in neutral,
advance throttle to approx.
1/8 throttle in short bursts, 5
to 7 times.

3. Use low range only when

towing or carrying loads.

4. Shift transmission to low

range carefully; use fast,
aggressive throttle
application to engage
clutch.

WARNING

Excessive throttle may
cause loss of control and
vehicle overturn.

Содержание 108.27807

















































































Результаты поиска

Содержание 108.27807

Отзывы:

Похожие инструкции для 108.27807

Бренды по названию

Популярные бренды

Craftsman 108.27807, Руководство оператора

Результаты поиска

Содержание 108.27807

Отзывы:

Похожие инструкции для 108.27807

Бренды по названию

Популярные бренды