manualshive.com logo in svg

CPS FA1000 SERIES, Руководство по эксплуатации

Поделиться
Скачать
CPS FA1000 SERIES Скачать руководство пользователя страница 17

MAINTENANCE MODES: DURING NORMAL OPERATION OF FA1000

FILTER CHANGE: 

The FA1000 uses a mass flow tracking system on how much recovered refrigerant has passed through the Filter Drier (CPS 

p/n ARXF5). Each 41 Cubic Inch Drier can handle 150 lbs. of refrigerant before requiring change. When it is determined that the filter has ex-

ceeded the 150 lbs., the unit locks out (if in SAE mode) the recovery function in both RECOVERY and FULL CYCLE. It is necessary to purchase 

a Filter Drier under CPS p/n ARXF5. Each new Filter Drier comes with a unique code to unlock the recover/recycle function. The FA1000 has a 

lower tilt drawer design to hold 2 spare filters.

The LCD will now read:

Push the 

START

 key to begin Filter Change routine.

FILTER CHANGE

DO NOT CONNECT

TO A/C SYSTEM

PUSH [START]

 

START >

 

QUIT >

 

CLOSE LIQUID PORT VALVE ON 

RECOVERY TANK

THEN PRESS CONTINUE

 

 

CONTINUE >

 

The LCD will now read:

After closing liquid port tank valve, push 

CONTINUE

 key.

Hint: To speed up filter cleaning, remove the filter 

from the bracket. Hang the filter so the hose coming 

from the back of the unit is on the bottom.

FILTER CHANGE

EVACUATING

FILTER

PLEASE WAIT

 

 

QUIT >

 

The LCD will now read:

The evacuation process will take about 2-5 minutes.

The unit will run until a filter has been evacuated.

When choosing the RECOVER or FULL CYCLE 

modes, the unit will remind the user to order a filter when the 

FILTER LIFE REMAINING is below 25%. 

The following is an example of the LCD when Filter Life

is less than 25%: Push the 

CONTINE

 key to proceed to filter 

change.

When the Filter Life reaches 0%, the following LCD screen will 

come up. Push the CHANGE FILTER key to begin filter change 

procedure. 

Note: pushing QUIT key at this time will return the unit to 

the Main Menu. While in the SAE mode, all functions except 

RECOVER and FULL CYCLE are active. To unlock RECOVER and 

FULL CYCLE modes, complete the filter change procedure).

RECOVERY WILL NOT BE ALLOWED 

WHEN FILTER LIFE EXCEEDED

ORDER P/N ARXF5

FILTER LIFE 

REMAINING 20%

 

FILTER CHANGE >

 

CONTINUE >

 

FILTER LIFE EXCEEDED.

RECOVERY NOT ALLOWED

REPLACE FILTER

WITH CPS P/N

ARXF5

 

CHANGE FILTER >

 

QUIT >

 

17

MAINTENANCE

Содержание FA1000 SERIES

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды