background image

COTES C30 

OPERATING AND SERVICE HANDBOOK 

  

page 42/48

 

Connection need for condensation (LK)- and Heat Recovery (HR) unit 

– Drain 

When installing a HR or LK unit, the unit must be placed in an upright position, with the bottom plate 

parallel to the horizontal plane. It is critical that the unit is positioned correctly, otherwise the water 

condensate will not be sufficiently drained. 

The heat recovery unit HR is equipped with one drain connection that has to be guided to the drain in 

the building as minor condensate may get formed inside the unit. 

The condensation unit LK is equipped with two drain connections found on the bottom of the unit. The 

drain connection to the left (seen from the front) is the main drain. 

For both the Heat recovery unit, and the LK unit, a hose must be mounted to the drain connections 

that guides water to a drain in the building. The hose that is connected to the drain pipe, must be of 

sufficient size and mounted on the outside of the drain pipe (see illustration on the next page). 

Minimum internal diameter of the Hose = 14mm 

For the LK/HR unit’s main drain, an “air-lock” must be made with, or in connection with, the drain 

hose, and must be minimum 30mm below the drain. Fo

r the LK unit, if an ‘air-lock’ is not in place, the 

low relative pressure inside the unit will pull outside air in, and stop the water from draining.  

The secondary drain does not need an air-lock. 

We recommend keeping some free space below the module to make sure it is easy to install drain 

hose(s) and an air-lock. An additional floor or wall bracket can be provided to make sure there is 

enough space. For details, please contact your Cotes dealer, or Cotes. 

 

 

 

 

 

NOTE 

Before the machine is started, t

he ‘air-lock’ must be filled with water, otherwise the unit may 

not function properly.

 

 

 

NOTE 

The two drain must not be connected by a Y connection and guided in one common hose to 

the drain in the building. Water has to float independently from each of the LK drain 

connections to the drain in the building. 

 

Содержание C30C

















































Отзывы: