Cotes C30C Скачать руководство пользователя | Manualshive

Страница: 31 / 48

background image

COTES C30

OPERATING AND SERVICE HANDBOOK

page 31/48

Service/repair work on this

dehumidifier

Service area must be clear at all time.

Diagrams and manual must be kept near the machine.

Machine will automatically startup in case of power loss and recover of electricity.

Safety instructions

Before opening the dehumidifier, make sure that the electric current is switched off at the mains
before you open top cover or front door.

For 400V models the safety switch should also be switched OFF and locked

You should never just turn off the power to the dehumidifier while it is running. The correct procedure

is to switch the rotary switch to neutral position, after which the machine runs a cooling cycle before

the regeneration air fan stops. Turning off the dehumidifier properly prevents any over-heating.

WARNING

Make sure that electric current is switched off at the mains

before you open top cover or front door

The safety switch should also be switched off and locked.

«
...
29
30
31
32
33
...
»

Содержание C30C

















































Отзывы:

Нет отзывов

Похожие инструкции для C30C

Бренд: Bionaire Страницы: 2

Бренд: HTW Страницы: 56

Бренд: Lowry Страницы: 22

Soleus Air R-HCT-D30-A

Бренд: TCL Страницы: 11

Бренд: MEI Страницы: 28

CH-D008WDP6-20LD

Бренд: Cooper & Hunter Страницы: 60

Бренд: Vicks Страницы: 37

Бренд: weewell Страницы: 32

Бренд: Brevi Страницы: 16

Бренд: Infiniton Страницы: 48

Бренд: Hoffrichter Страницы: 32

Бренд: Infiniton Страницы: 54

Бренд: Skuttle Indoor Air Quality Products Страницы: 1

Бренд: Munters Страницы: 32

Бренд: Emerson Quiet Kool Страницы: 24

Бренд: TurMix Страницы: 15

Бренд: Sunpentown Страницы: 4

Бренд: MOOKA Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды