CORNING OptiTect EVO-707-EN Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 25

CORNING OptiTect EVO-707-EN Скачать руководство пользователя страница 12

STANDARD RECOMMENDED PROCEDURE 003-737 | ISSUE 4 | MAy 2015 | PAGE 12 OF 25

• Maximum of seven splice trays can be accommodated within the splice housing (one

reserved for Feeder splicing and six for Distribution splicing). Each splice tray holds six

heatshrink mass fusion splices for a maximum of 72 splices per tray.

• Feeder splicing occurs in the bottom splice tray in the splice housing with Distribution

splicing in subsequent trays above.

• Two sub-units (jacketed or braided tubing) with three 12-fiber ribbons per sub-unit can be

strain-relieved to each feeder splice tray.

• Two sub-unit pigtails from the back of the Input Fiber Field panel to the feeder splice tray are

pre-routed at the factory and stored for splicing.

• Two sub-units (jacketed or braided tubing) with three 12-fiber ribbons per sub-unit strain-

relieved to each distribution splice tray.

• Two sub-unit pigtails from the back of the Distribution panel to the distribution splice tray are

pre-routed at the factory and stored for splicing.

10.1 Feed Cable into Enclosure

CAUTION:

Fiber optic cable is sensitive to excessive pulling, bending, and crushing forces.

Consult the cable specification sheet for the cable you are installing. Do not bend the cable

more sharply than the minimum recommended bend radius. Do not apply more pulling force

to the cable than specified. Do not crush the cable or allow it to kink. Doing so may cause

damage that can alter the transmission characteristics of the cable; the cable may have to be

replaced.

Step 1:

Open the interior swing panel by lifting the

latch on the right side of the panel to access

the cable entry/exit location of the enclosure.

Step 2:

Determine where the cable will enter the

enclosure and remove the appropriate knock-

out.

Step 3:

Loosely install a watertight fitting into the

hole from which the knock-out was removed.

Select the appropriate feeder or distribution

cable installation kit for the cable being

installed. One kit for each cable size is

provided.

Step 4:

Feed the cable through the fitting into the

enclosure (Figure 13).

Watertight Fitting

O-ring

Locknut

KPA-0896

Figure 13

«
...
10
11
12
13
14
...
»

Содержание OptiTect EVO-707-EN


























Отзывы:

Нет отзывов