SPECIFICATIONS AND TECHNICAL DATA
SPECIFICATIONS
MODEL
SN50S5
SN50S4
SN50GSI
SN50S5LM
SN50S53LM
SN40P/ SN40P-R
SN40S2/ SN40S2-R
SN40GSW/ SN40GSW-R
HEIGHT- in (mm)
10.7" (272)
10.7" (272)
10.7" (272)
9.9” (251)
WIDTH- in (mm)
3.7" (94)
3.7" (94)
3.7" (94)
3.7" (94)
LENGTH- in (mm)
14.3" (363)
22.4” (570)
30.6” (777)
14.3" (363)
WEIGHT- Lbs (kgs)
5.1 (2.3)
5.9 (2.7)
6.8 (3.1)
5.5 (2.5)
RECOMMENDED OPER. PRESS.
70 to 120 psi (5 to 8 bar)
LOADING CAPACITY- Staples
160
310
460
160
AIR CONSUMPTION at 90 PSI (6 bar)
1.9 cfm (0.9 liter/sec).
1.7 cfm (0.8 liter/sec).
FASTENER SPECIFICATIONS
MODEL
SN50S5/ SN50S5LM
SN50S53LM
SN50GSI
SN50S4
SN40GSW
SN40GSW-R
SN40S2
SN40S2-R
SN40P
SN40P-R
LENGTH
-
in(mm)
1"~2" (25~50)
3/4”~1-9/16” (19~40)
CROWN-in(mm)
7/16” (11.1)
7/16” (10.6)
7/16”(11.2)
1/2”(12.5)
15/16”(23.8)
1”(25.4)
1-1/16” (26.4)
THICKNESS-in(mm)
0.055” (1.40)
0.051” (1.30)
0.055” (1.40)
WIDTH-in(mm)
0.062” (1.60)
0.057” (1.45)
0.062” (1.60)
GAUGE
16
17
16
TOOL AIR FITTING
This tool uses a 1/4-18 N.P.T or 1/4-19 P.T. male plug. The inside diameter should be .200” (5 mm) or larger. The
fitting must be capable of discharging tool air pressure when disconnected from the air supply.
OPERATING PRESSURE
70 to 120 PSI (5 to 8 kg/cm
2
). Select the operating pressure within this range for best fastener performance.
DO
NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.
TECHNICAL DATA
AIR CONSUMPTION
Tool air consumption:
SN50-1.9 cfm (0.9 liter/sec), SN40-1.7 cfm (0.8 liter/sec)
of free air to operate at the rate
of 100 nails per minute, at 90 PSI (6.0 kg/cm2). Take the actual rate at which the tool will be run to determine the
amount of air required. For instance, if your fastener usage averages 50 nails per minute, you need 50% of the
tool air consumption in running at 100 nails per minute.
NOISE
A-weighted single-event sound power level LWA,1s:
SN50-107.4, SN40-105 dBA
A-weighted single-event emission sound pressure level at work station LpA 1s,d:
SN50 -106.9, SN40 -104.7 dBA
These values are determined and documented in accordance to EN12549.
VIBRATION
Vibration characteristic value:
SN50-3.46, SN40-5.13 m/s
2
These values are determined and documented in accordance to ISO 8662-11.
This value is a tool-related characteristic value and does not represent the influence to the hand-arm-system
when using the tool. An influence to the hand-arm-system when using the tool will, for example, depend on
the gripping force, the contact pressure force, the working direction, the adjustment of mains supply and the
workpiece support.
4
