manualshive.com logo in svg

Cooper F6-PA-LS, Инструкция по установке и эксплуатации, Страница: 45 / 48

Поделиться
Скачать
Cooper F6-PA-LS Скачать руководство пользователя страница 45

Control-Powered Type NOVA reclosers with serial numbers 

100,000 and above, as listed in Table 13, require a VTC-

ready control. They are equipped with a 19-pin control 

cable receptacle and can be identified by labels prominently 

displayed on the bottom of the recloser tank and on the 

side near the 19-pin receptacle, as shown in Figure 38.
For more information on the Control-Powered NOVA 

Interface, refer to 

Service Information S280-42-1

S280-70-10

45

CAUTION: 

Equipment Misoperation. The 

control-powered NOVA reclosers that require a 

VTC interface must be used with VTC-ready controls. 

Failure to use a VTC-ready control will result in failure to 

trip or close. 

G144.0

Figure 38.

Receptacle side view and bottom view of NOVA 

recloser tank, showing placement of VTC label.

TABLE 13

Serial Number Break for Control-Powered NOVA Reclosers 

with VTC

 

Control-Powered NOVA 

Serial No.

 

NOVA15  

100,000

 

NOVA27  

100,000

 

NOVA38  

100,000

Note:

  Control-powered NOVA reclosers with serial numbers 

below those listed in Table 13 do not require a VTC-

ready control. Refer to the recloser nameplate for the 

serial number.

RECLOSER VTC INTERFACE

Содержание F6-PA-LS

















































Отзывы:

Нет отзывов