Cooper & Hunter CH-HP3.5SWNK Скачать руководство пользователя

Страница: 47 / 47

Air Source Heat Pump Water Heater

The water heater stops operation and
the wired controller displays UP

Power protection of inverter fan

The water heater stops operation and
the wired controller displays AE

Detection circuit malfunction of driven
current of inverter outdoor fan

The water heater stops operation and
the wired controller displays AJ

Desynchronizing protection of inverter
outdoor fan

The water heater stops operation and
the wired controller displays A6

Driven communication malfunction
between main control and inverter
outdoor fan

The water heater stops operation and
the wired controller displays A8

High temperature protection of driven
module of inverter outdoor fan

The water heater stops operation and
the wired controller displays A9

Malfunction of temperature sensor of
driven module of inverter outdoor fan

The water heater stops operation and
the wired controller displays An

Malfunction of drive storage chip of
inverter outdoor fan

The water heater stops operation and
the wired controller displays AU

Drive charting loop malfunction of
inverter outdoor fan

The water heater stops operation and
the wired controller displays AP

Abnormal protection of driven AC input
of inverter outdoor fan

The water heater stops operation and
the wired controller displays Ar

Malfunction of temperature sensor of
drive electric box of inverter fan

The water heater stops operation and
the wired controller displays U9

Zero-crossing protection of drive AC
input of inverter fan

The water heater stops operation and
the wired controller displays EE

Malfunction of storage chip of main
control

There’s harsh sound during operation;
There’s off-flavor during operation;
Air switch or leakage protection switch
breaks off frequently.

There may be risk for the safety.
Please stop operation immediately
and cut off the power.

After-sales service

If there’s quality or other problems for the

C&H

products, please contact with

C&H

local appointed maintenance center.

Содержание CH-HP3.5SWNK
















































Результаты поиска

Содержание CH-HP3.5SWNK

Отзывы:

Похожие инструкции для CH-HP3.5SWNK

Бренды по названию

Популярные бренды

Cooper & Hunter CH-HP3.5SWNK, Руководство пользователя

Результаты поиска

Содержание CH-HP3.5SWNK

Отзывы:

Похожие инструкции для CH-HP3.5SWNK

Бренды по названию

Популярные бренды