Cooper & Hunter CH-HP3.5SWNK Скачать руководство пользователя

Страница: 35 / 47

Air Source Heat Pump Water Heater

Pressure gauge

Low pressure valve

High
pressure
valve

Fluoride injection

mouth

Fluid pipe

Fluid valve

Hex key

Air pipe
Air valve

Injection
hoses

Refrigerate bottle

Figure 12-1 Refrigerant replenishment diagram

Fluoride injection

mouth

Fluid pipe
Fluid valve

Hex key

Air pipe

Air valve

Figure 12-2 Refrigerant discharging diagram

13 Method for Refrigerant Reclamation

Refrigerants can be reclaimed for the source water heater only in specific mode.

In normal hot water mode, press and hold MODE+



for 5 seconds to enter the

query status. When the temperature display area displays 00, press and hold

MODE+



for 5 seconds. Then, 00 changes to P0. Press the





button to

switch to the P3. Then, press the MODE button for settings. Press the





button

again to change 00 in the time display area to 01. Press MODE to enter the

defrosting mode, and complete the settings for refrigerant reclamation settings. After

the settings are complete, first close the fluid valve (smaller valve), and when the

there is cold air blowing out from the outlet, immediately close the air valve (larger

valve). After it is closed, immediately shut down the unit

Caution

Refrigerant reclamation must be promptly completed, so as not to cause any

Содержание CH-HP3.5SWNK
















































Результаты поиска

Содержание CH-HP3.5SWNK

Отзывы:

Похожие инструкции для CH-HP3.5SWNK

Бренды по названию

Популярные бренды

Cooper & Hunter CH-HP3.5SWNK, Руководство пользователя

Результаты поиска

Содержание CH-HP3.5SWNK

Отзывы:

Похожие инструкции для CH-HP3.5SWNK

Бренды по названию

Популярные бренды