Cooper & Hunter CH-HP3.5SWNK Скачать руководство пользователя

Страница: 42 / 47

Air Source Heat Pump Water Heater

Precautions for Safety Use

(1)

For comfort usage, it's

suggested

to use shower head with flow rate of 6 ~

7L / min.

(2)

User

should

have regular check and maintenance for heat pump water

heater, if there is abnormal condition, please immediately contact

after-sales

service for help so as to guarantee normal, safe and

reliable

unit operation.

(3)

Regular check and replace the magnesium bar is necessary. Customer

can contact

serviceman for replacement. Recommended replace period is 2

~ 3 years.

(4)

Cut off the power supply prior to any maintenance or services. A

non-professional personnel is not allowed to adjust or service the heat pump water

heater.

(5)

Improper operation might cause scald due to hot water. Water

heating without enough water might produce high-temperature steam or

hot water, which might cause serious scald. Hence, guarantee the water tank is

filled with water.

(6)

The water heater is equipped with safe relief valve for reliable operation,

please do not change its location and never block its outlet. The pipe should be

directly connected to floor drain.

(7)

Never drink the water inside the water tank.

(8)

Children bath should be supervised by adults.

(9)

This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or instruction concerning use of

the appliance in a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not be made by

children without supervision.

(10)

In order to prevent danger caused by water tank electric heater failure, a

thermostat is equipped in the electric heater circuit; once the water temperature

reaches 75

℃

, the thermostat will cut off the power supply for the electric heater. In

spite of this protection, when there is electric heater anomaly, please contact C

professional service people for maintenance or replace.

（

）

The inlet water pressure range for water tank is 0.02MPa~0.7MPa, it is

necessary to confirm the pressure range before installation.

Содержание CH-HP3.5SWNK
















































Результаты поиска

Содержание CH-HP3.5SWNK

Отзывы:

Похожие инструкции для CH-HP3.5SWNK

Бренды по названию

Популярные бренды

Cooper & Hunter CH-HP3.5SWNK, Руководство пользователя

Результаты поиска

Содержание CH-HP3.5SWNK

Отзывы:

Похожие инструкции для CH-HP3.5SWNK

Бренды по названию

Популярные бренды