manualshive.com logo in svg

Cooltrax UMD V3, Руководство пользователя

Поделиться
Скачать
Cooltrax UMD V3 Скачать руководство пользователя страница 29

UMD V3 Installation Manual - Remote Control  

13 November 2018 

Page 

29

 of 

39

 

CoolTrax Interface Plug

 

 

If these two measurements are correct, connect the fridge interface cable to the UMD COMM 2 Port and power ON the 
UMD (If not already ON). 

If the Fridge cable was connected to a UMD that was OFF and then powered ON after the connection was made, the 
UMD should sense the fridge within a couple of minutes and the fridge light on the UMD should come ON RED. 

Note:

 the recommended firmware revision for the HDMI on Carrier Advanced Controller fridges is 

Revision 04.12. This 

works on European Vector and American versions of the fridge and allows for remote two-way control of 
each. Sometimes if the firmware is a lower revision the fridge interface can fail and an upgrade is 
recommended.

 

 

Fault: The Reefer Will Not Turn On with the Local Switch 

After fitting the Cooltrax System the Reefer will not turn on normally using the local On/Off Switch 

Actions: 

If the Reefer has a standard controller and you have upgraded the EPROM check that the EPROM is seated 
correctly 

Check wiring looms and make sure you haven’t accidently unplugged a cable while looking for the Serial Port 

Plug which is often tucked behind the controller on older model Reefers. 

Check Battery Voltage on the Reefer Battery if it is below 12.3DCV you will need to charge the battery as it will 
not start the reefer at this level. 

Fault: The UMD will not Power On or is running on Internal Battery 

If there is no Power to the UMD the Green Power LED at the bottom LH corner of the LED array will be off. 

Note: If the UMD has been previously powered up for a reasonable time it will run on internal battery for 3 
hours or so (if battery is fully charged). In this case the Red Battery LED will be illuminated on the bottom RH 
side of the LED array. 

 

Actions: 

Содержание UMD V3








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды