Cool Energy inverTech CE-iVT18 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 37

background image

Page | 21

Cool Energy inverTech Manual v6.6 2020 ©

3.

Time Zone / Clock Settings:

If the internal time clock is being used to control, heating / water or cooling times it can be set using the
following procedure. If it is not being used and you are using external controls, the fields should be left blank
and turned off.

Press

to access menu

Using

↑

↓

buttons select Time Zone / Clock

Press

to confirm

Use

↑

↓

Buttons to change the settings

Press

to confirm.

Upto 3 time zones can be set over 7 weekdays.
The temperature setpoints can also change based on the time zone.

Ask you installation engineer for advice on settings for the best efficiencies.

«
...
19
20
21
22
23
...
»

Содержание inverTech CE-iVT18






































Отзывы:

Нет отзывов

Похожие инструкции для inverTech CE-iVT18

Бренд: Balboa Страницы: 2

Бренд: Jaga Страницы: 2

Бренд: Wayne Страницы: 16

Aqua-Pure AP510

Бренд: 3M Страницы: 16

Бренд: IBC Страницы: 18

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 76

Бренд: Walrus Страницы: 6

Бренд: Wallgate Страницы: 3

Бренд: wallas Страницы: 124

Бренд: wallas Страницы: 36

Бренд: Walrus Страницы: 4

Бренд: AmeriWater Страницы: 16

Бренд: Prem-I-Air Страницы: 7

Бренд: Olimpia splendid Страницы: 96

FLOOD KING 240V

Бренд: U.S. Products Страницы: 8

Бренд: Navien Страницы: 131

Trumatic S 2200

Бренд: Truma Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды