Control Techniques UD52 Скачать руководство пользователя страница 19

Страница: 19 / 36

UD52 User Guide
Issue code: 52nu3

Using position information for orientation

The position value in parameter

16.04

COS

encoder incremental position

(coarse)

(at 16384 counts per revolution) is used as an input to the position-

control algorithms in Menu 13. This allows orientation to be performed
within one revolution.

Using position information for digital lock

The digital-lock algorithm uses only incremental changes in position
obtained from parameter

16.04

and ignores the multi-turn information in

parameter

16.03

COS

encoder – revolution count

Only incremental digital lock is performed; multi-turn absolute orientation is
not supported.

5.4 Simulated-encoder

outputs

(terminals 50, 51, 53, 54)

The simulated-encoder outputs can be connected to external equipment for
monitoring the output of either a

SIN-COS

encoder connected to the UD52

or the main encoder (Encoder 1) that is connected to the 15-way D-type on
the Drive. By default, the

SIN-COS

encoder is used as the source. To select

Encoder 1, set parameter

16.06

Simulated-encoder output select

at 1.

Quadrature AB, or frequency and direction

By default, the simulated-encoder outputs are phase-quadrature

and

signals. For frequency (

) and direction (

) signals, set parameter

16.08

imulate

d encoder – F/D output enable

at 1.

Pulses per revolution

The simulated-encoder outputs are derived from the polarity changes in the

SIN-COS

encoder outputs, giving a resolution of four times the number of

encoder lines per revolution.

The number of pulses per revolution (

PPR

) is dependent on the number of

lines per revolution of the

SIN

COS

encoder as well as on the value

16.07

Simulated-encoder output scaling.

By default, the outputs are scaled 1:1 . To change the scaling, enter the
required value in parameter

16.07

Simulated-encoder output scaling

. The

scaling factor is given by the following:

16 07

[

]

Содержание UD52





































Результаты поиска

Содержание UD52

Отзывы:

Бренды по названию

Популярные бренды

Control Techniques UD52, Руководство пользователя

Результаты поиска

Содержание UD52

Отзывы:

Бренды по названию

Популярные бренды